Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Door Lock Switch Assembly by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18035460
Manufacturer Part Number: WP8182634

Washer won't start or door won't latch? This door lock switch assembly detects if the door is closed. DIY-friendly repair with video guide included.

More
$79.51

IN STOCK
Ships Tomorrow Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Washer Door Lock Switch Assembly (Part Number: OEM18035460)

George A. for Model Number Kitchen Aid KHWS01PMT3

I have a front loading washer that seems to give random errors if it isn't in a good mood. Most of the time it works fine, however. Recently it has refused to lock and the FdL error appears. At first it would sometimes work by unplugging and plugging it back in but now it shows the error always. I purchased the part 8182634 Door Switch Assembly and replaced the old one. Based on some of the responses here, I felt it was a good bet. I was wrong. It has not helped at all. The error code continues. Any ideas? Thanks

1 Answer

George, Since you've replaced the lock assembly, you'll need to check the wiring harness between the latch assembly WP8182634 and the CCU WPW10137702 especially the connectors at the CCU. If all's Ok, check and make sure the outlet is, 120 VAC, polarized and grounded and replace the CCU.

Read More...
Jerry S for Model Number Whirlpool Duet Washer Model GHW9400PW0

I have had a problem for a while where I get a door lock error dl and F. I have been putting up with this for some time now where I try opening and closing the door, unplugging and plugging it back in, I even have resorted to banging on the top right and it starts, based on a report I read. A couple weeks ago while it was in a spin cycle, it got out of balanced and the door broke open breaking the latch. I have been taping the door shut and it works, now it will not finish cycles. It stops in the wash cycle, it stops in the rinse cycle and stops in the spin cycle. Helps

1 Answer

Hello Jerry. It sounds like you need to replace the door lock assembly on the unit.

Read More...

1 Answer

Jack, Presumably you had a "DU" or "DL" error code. There is a possibility that the damaged door latch assembly could have damaged the CCU, but it's not as common on this model washer as the wholesaler suggested. You do want to recheck and make sure all the wiring harness connectors are properly seated in the board connectors and routed properly through the cabinet. Also check and make sure the door and door strike are properly aligned and engaging the latch assembly properly to the front panel, before you replace the CCU WP8182689.

Read More...

1 Answer

Tommy,

These error codes are both the same and represent an door lock error. You will want to check the wire harness and the connections. If these check ok then most likely the door switch assembly is faulty and needs to be replaced.

Read More...

1 Answer

Georgia,

The F11 error code is a motor control failure: The Motor Control Unit has internal failure. If failure occurs during high-speed spin the door unlocks after 3 minutes. This error code is only shown in Diagnostic test. Possible Causes/Procedure - Verify the shipping system including shipping bolts and spacers are removed, and power cord out of the unit. - Check if washer is on a dedicated circuit. Other devices on same circuit can create line noise and cause this issue.
- Un plug washer or disconnect power - Check the neutral feed to the MCU and CCU from the AC line filter.
- Check allwire harness connections between the Motor & MCU, and MCU to CCU,
are not broken orwires detached and connector internal pins are visible.
- Make sure that all the connectors are fully seated.
- Plug inwasher or reconnect power cord.
- Verify the unit operation by running the Diagnostic Test cycle. See page 5.
- After the diagnostic test has finished, unplugwasher or disconnect power cord
andwait for 15 seconds.

Read More...

1 Answer

Hello Sean. Based on the error code provided, it sounds like the door lock assembly will need to be replaced on the unit.

Read More...

1 Answer

Walter,

You will want to check to make sure that the drain is not clogged up. If the drain is slow or clogged it will cause the unit to not go into the spin cycle. Also check to make sure that the door lock assembly is good. An intermittent door lock will cause no spin issue.

Read More...

1 Answer

Hello Dixie. Unplug the unit. Remove the pressure switch hose and blow through the hose. Once the chamber is clear, if the code continues, replace the pressure switch. If it is still there, then the board will have to be replaced.

Read More...

1 Answer

Hello Maria. First thing to check is the wiring harness. Last thing to replace is the board. Most likely bad connection on the wiring of the unit or a bad wire.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google