Danny May 23, 2013 for Model Number KAWE777BWH1 Hello, Before puchasing the water pump for my Washing machine, I need to remove the pump which is leaking and needs to be replaced. How best to remove a rusted shaft water pump off the motor for replacement? Thank you. Danny
1 Answer Hello Danny. Pull the pump off the shaft is the only way. Then use some sand paper to clean the shaft of the motor as best as you can so the new pump slides onto the shaft without forcing it. Read More...
Suzanna May 14, 2013 for Model Number GSQ9611KQ1 My wash will not empty the water out. It washed the clothes fine but it did not empty or spin out the water.
1 Answer Suzanna, You will want to check the drain pump to make sure that it is not clogged and make sure that it spins freely. If not then you will need to replace the pump. Read More...
Ed May 05, 2013 for Model Number LSL9345EQ1 Awhile back I replaced the parts that make washer aggatate. I could'nt get the pump off, so I just moved pump still attached to the motor to one side. Now the pump leaks[bad), the pump was so stuck onto the shaft that I had to take it off in pieces. My ? is there's a piece of plastic about 3/4 in long or less still on shaft, does this stay or does it have to be taken off? Thanks
1 Answer Hello Ed. It must come off. Then you will use sandpaper to clean up the shaft. There should be 2 flat sides and 2 rounded sides on the motor shaft. All should be metal. Read More...
Nova May 03, 2013 for Model Number LTE6234DQ2 Washer is not draining. Once in the drain cycle the motor knob that spins the pump is not spinning. There is nothing clogging the pump assembly...What is wrong?
1 Answer Hello Nove. If the motor is turning, but not the pump, you will need to order and replace the pump. It is bad. Read More...
Michele April 27, 2013 for Model Number GST9675JQ0 The water will not drain out during the spin cycle. It does spin, but the water will not drain. We can lower the hose and manually drain the water, but it's not being forced out during the spin cycle. We replaced the direct drive motor coupling, but this did not fix the issue. Could it be the drain pump?
1 Answer Michelle, You will want to pull the pump and check to make sure that there is nothing clogged in the pump which would restrict if from pumping out. If there is nothing clogged in the lines or in the pump then you would want to replace the pump assembly. Read More...
Robert April 16, 2013 for Model Number Kenmore After a wash or rinse cycle, the water remains in the tub until the spin cycle starts, then the water is "thrown" out of the washer. Is this a drain pump issue (don't hear any motor noise during the part of the cycle is should be draining) or a timing/timer issue? I haven't pulled the pump off, waiting till I get a new one (if that is the problem).
1 Answer Robert, Either the pump is clogged or bad, which would cause the issue that you are describing. Read More...
Adrian April 13, 2013 for Model Number Whirlpool After the wash is done my clothes are still soaking wet (as oppose to just damp like before). I do not however see any pool of water at the bottom though. I also took out the pump but but don't see any physical damage. I can also rotate the 'wheel' with my fingers tough not freely. There is some tension but then again I'm not sure if that's how it's suppose to be.
1 Answer Adrian, There will be just a little bit of resistance when turning the pump. You want to look into the pump and make sure that there is nothing in it that could cause a slow drain. Read More...
Daniel October 29, 2012 for Model Number 11026955690 have a kennmore 90 electric series---cf 3402408 stcok 26955 and i get a message that reads ol i guess 4 over load--- and i cant get the water to drain out---- do i need a pump
1 Answer Daniel, Yes, you do need to check the drain pump WP3363892 and drain hoses for obstructions and or a seizing pump. This could cause the "OL"(overloaded) error code, in either the agitate or spin cycles. The control board is looking for a specific amount of Resistance/ RPM in a specific amount of time, and will display the code if not reached. Also check the Drive Coupler 285753A for cracked or broken pegs, or excessive wear and tear. Read More...
Gonzalo July 10, 2012 After a cold night the washer machine got fill of water. Did the water pump get broke, or is something else?
1 Answer Hello Gonzalo. Based on the information you provided, it sounds like the water valve is bad on the unit and will need to be replaced. Read More...
Pamela March 12, 2012 for Model Number LTE6234DQO After my wash has completed the cycle, there is a slow drip that comes into the tub from the white item that water shoots down from when filling the tub to wash clothes. What part do I need to fix this?
1 Answer Hello Pamela. The slow drip can be attributed to one of 2 things. First is water pressure. I would check the facet an insure it is turned all of the way on. Also, you should check the screen on the water valve (where the hose hooks to the back of the machine). If it starts to stop up with mineral deposits or sedimentation from the water line, this can prevent sufficient water pressure to get to the actual valve to close the valve completely. (The water valve is closed by water pressure). The other thing that can cause it is the water valve 285805 is actually failing. Check the obvious before buying any parts but remember, the part,(if needed), is cheaper than the cost of repairing water damage! Hope this was helpful. Have a great day! Read More...