David H December 09, 2012 for Model Number WDG5100SQ I have replaced 3 rear drum rollers (same one each time on the right side). I barely get a dozen uses before the rubber on the wheel breaks. Is there a better quality roller available? or is there a problem that rings a bell with this condition? The dryer isn't overloaded with clothes and the roller does sit in the drum guide.
1 Answer Hello David, You may want to check your bulkhead to make sure that it is not bent. If the roller is not sitting perfectly straight then it will chew the rollers up. Read More...
Jojo March 29, 2012 How do I know if I need to replace the shaft or support roller of my dryer if it is making a thumping noise?
1 Answer Hi Jojo. With the dryer drum removed, carefully look at the drum weld area. When the weld area passes by the drum roller this is initially where the drum gets its thumping sound. If you feel the drum weld is excessive replace it. The roller which is normally closer to the heater can will catch the heat (especially with a vent restriction) and weaken the roller.Then the oil-impregnated shaft will loose its properties faster and wear out. Roller part # 349241T. You need to spin the roller and listen for squeaks. If the belt tensioner roller is worn it will also squeak part # WP691366. Thank you. Read More...
Ccaid January 29, 2012 for Model Number LER4634pQO My dryer was running really hard and loud. We have realized one of the drum rollers went bad so we looked on your website to get replacements. I found the correct ones but everything I see makes it seem like the drums usually need to be replaced when the bearing goes bad. The drum that I took off was completely wore down. The black, I'm assuming rubber, around the drum is completely gone and wore down to the plastic. My concern is that there is some underlying prblem that caused the rubber on the drum to grind down like that. I don't want to buy a new one just to have the same thing happen in a couple of weeks. I guess my major question is, is it at all normal for the rubber around the drum to completely grind down? The other drum looks fine. Also we just got this dryer from my wifes brother and it looks as if maybe it were dropped at one point, one side of it is a little bent. Another thing that is weird is that the other drum looks fine. It seems like if something was out of place it would grind both down, I don't know? Look forward to your response.
1 Answer Hi Ccaid. All drums are made from a flat piece of steel. Then formed by rollers on each end section of the drum. Then they weld the ends (or sides) together and sometimes as the drum rollers pass by the weld seam it has a "bump" noise that is synonymous in all dryers. Inspect the drum weld and see if it is minimal (or livable) standards. If not it is part # 697760. The drum rollers all wear because of 1-one placed above the heater can assy. that catches all the heat, then become out of round. Rear roller kit part # 349241T. Rear Drum Support Roller Kit - 2- pack. Fits all Whirlpool made dryers (Whirlpool, Kenmore with prefix 110, Roper, Kitchen Aid, and Estate). Roller kit comes with 4 tri-rings and one retaining washer. Matching belt 341241 and idler pulley WP691366. Whirlpool dryer repair manual if needed - 677818L. If the vent system clogs and the outside vent cap doesn't open/close properly then this will overheat all internal parts causing premature failures and fires. The rear felt wears and is part # 239087. Along w/ the front glide bearing ring will off-set a tub. Part # WP3394509. Thank You. Read More...
Dave December 15, 2011 for Model Number lgq8858hq0 Dryer will start to sqeal about 30sec. after startup. It gets worse then eventually stops running. Could this be the drive belt or something more complexe? Thank You.
1 Answer Hello Dave. You will need to check the rollers 349241T and the idler pulley WP691366 and make sure they are not locked up. If they are good, and the drum turns freely by hand, you will need to replace the motor 279827. Hope this helps. Read More...
Frank G. August 01, 2011 for Model Number LEQ703KQ1 From reading other costomers questions about the problems with replacing the belt,pulleys and roller pins, it appear as if there is a defect in the machine. What asurance do I have that if I spend almost $50 dollars for these items that I wont have the same problem. I did not read where any of you customers problems were solved. Is there some kind of warranty offered by you, or do I just loose out.
1 Answer Frank, Just like any other manufactured product, life expectancy is dictated by proper usage, wear and tear etc. The parts you purchase from AppliancePartsPros.com, have a 1 year 365 day warranty, one of the longest parts warrantys in the industry. Thanks and Good Luck Read More...
Annette M. April 30, 2011 for Model Number kenmore gas dryer 110.77902792 Will the rear support rollers AP3098345 fit?
1 Answer Hello Annette! It does not seem that the roller kit 349241T will fit on your Kenmore model 110.77902792. The correct rollers will be part number WPW10314173. This part comes one per package. Thanks. Read More...
Coach R. April 07, 2011 for Model Number LEB6200KQ1 Developed a flat spot on the roller (mainly on the lower one) so I replaced both and the belt for good measure. 3 weeks later, lower roller is already mis-shapen. Had it for 10 years, one set of rollers. Replaced 28 days ago, now needs replacing. What am I missing?
1 Answer Hello Coach. Did you change the roller support shafts WPW10359270 WPW10359269 with the new rollers? If these are worn, there will be alot of play in the rollers. Also, check the felt seals and front bearings and make sure they are good as well. Hope this helps. Read More...
Marlonrom March 31, 2011 for Model Number 110.62822101 Re follow up on request for assistance yesterday, above is the model number of my electric dryer. Will appreciate if you can assist identifying necessary parts I need to replace to eliminate grinding noise at dryer start up. Thank you PS: I've already replaced heating element, fuses and belt.
1 Answer Hello Marlonrom. You will need to chek and make sure there is nothing inside the blower wheel WP694089. If it is good and clean, then check the rollers 349241T and idler pulley WP691366 and make sure they are not tight and dragging. Hope this helps. Read More...
Marlonrom March 30, 2011 for Model Number Kenmore with lint on top model Hello. Each time I switch the dryer on, it starts with a grinding sound and disappear after a minute or two. I would like to fix the problem before it get worse. Can you give me an idea which part (s) I need to buy from you to fix this noise once and for all? I've already replaced heating element, fuses, belt and did a thorough cleanup and now this? Thanks for any assistance. Marlonrom
1 Answer Hello Marlonrom. We will need your model number to help you with this. Check the rollers and the idler pulley for wear. Hope this helps. Read More...
Joe March 23, 2011 for Model Number LER5636PQ0 I have a whirlpool electric dryer and the drum is loose, leaving burn marks on clothing. What do I need to do?
1 Answer Hello Joe. Check the drum seals, W11035878 front, W10612022 rear, and make sure they are good and not torn. Also check the rollers 349241T and make sure they are ok. Hope this helps. Read More...