Ernie May 29, 2011 for Model Number EDE5JHGXRL00 In the notes for this part it states that this unit does not work on unit's with the ice auger in the door. Mine has an ice dispenser in door for cubes and crushed but the thing that pushes the ice is on the bottom of the ice tub. Will this unit still work?
1 Answer Hello Ernie. 4317943 is indeed the correct part for your unit. While your dispenser is on the door, the auger itself is in the ice bin. I hope this info helps. Read More...
Bob May 29, 2011 for Model Number 596.72282202 I previously asked a question about my non funtioning ice maker and you were correct, the water tube was frozen. I thawed and cleared the tube and the icemaker worked perfectly for a week, then started freezing up again at the tube and started water dripping into the bottom of the freezer and ice collection tray. I cleared the tube a second time with the same result. Is it the secondary water valve causing the problem or the ice maker itself. If it is the valve where is its location?
1 Answer Hello Bob. Yes, you will need to replace the water valve 12002193. It is located on the back of the refrigerator. You will need to remove the lower back cover to replace it. Hope this helps. Read More...
Doug May 28, 2011 for Model Number msd2651hew Icemaker spontaneously quit. It will however make ice if you load the bin with ice, it will make about one tray, then quit. Sometimes it will make one. It seems to fill the tray with water, then that's it. I took the front cover off the timer and it doesn't seem to be running. What is the black section in the red wire on the harness running to the icemaker unit? Could it be the harness or more likely the icemaker unit itself? Thanks for your input and help, Doug.
1 Answer Hello Doug! You will need to replace the icemaker assembly. Your part number is D7824706Q. Thanks. Read More...
Rusty May 25, 2011 Water not flowing through water valve. Ohms out as closed. Don't know if the power is coming from ice maker. Is it valve or ice maker?
1 Answer Hello Rusty. You will need to cycle the icemaker and see if it is sending power to the water valve. If so, and the valve does not open, you will need to replace the water valve. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Seetha May 16, 2011 for Model Number kenmore model # 10652762100 Kenmore model # 10652762100. I am looking for Icemaker kit. If you have any kits please email me with link.
1 Answer Hello Tom! The icemaker D7824706Q does not include the valve, it is the ice maker only. If you are needing a valve, please supply your appliance model number. Thanks. Read More...
Tom K. May 15, 2011 for Model Number GX5FHDXTB00 Old icemaker stopped working. Took out unit and found massive mineral buildup/corrosion at one end of the u shaped silver tube that is on the bottom of the unit. The end of the tube is gone and the screw is exposed. As far as I can tell from the parts blowout list, it appears that item number AP4135008 is the only way to replace the silver tube. I have two questions: 1. Is the only way to replace the corroded silver U shaped tube to order the entire part number AP4135008? 2. If I order this part, does it include the water valve or do I need to order one separately? (I'm assuming a water valve leak created the corrosion/mineral buildup) Thank you in advance.
1 Answer Hello Tom. Yes, according to the model number and the information you gave, you will need to replace the icemaker D7824706Q. Hope this helps. Read More...
Dennis S May 14, 2011 for Model Number Amana M/N SRD25S5L My ice maker was cycling very slowly. Twelve hours or more between making batches of ice. We were using ice faster than it being made. When it did cycle it would properly discharge the ice and then fill the tray for the next batch well enough, but it would not eject the ice for a very long time. I ordered a replacement ice maker ( P/N AP4135008) the order sheet used P/N D7824706Q...The new ice make fit very well so I assume it is the correct replacement. However now I get no ice at all. The tray is not filling and so no ice. Any suggestions? Thanks
1 Answer Hello Dennis. Did you reinstall the bail arm on the new icemaker and pushed it down to turn the icemaker on? Also check and make sure the plug going into the icemaker is cliped and locked into place. Hope this helps. Read More...
Norm St. P May 13, 2011 for Model Number model # thi21s3w MFG# p1194704ww & ser# 9503150904 New Icemaker will not work. New Icemaker came with female connector. Old one was male. I will splice it to make it work. Can you provide the wiring diagram for the 4 wires to hook up my icemaker. The wires are different colors ----same amount of wires.-----My icemaker connector wires need to be spliced in the old fridge's connector wires. Colors of the old connector wires----black, brown, green, & white. New icemaker connector wires----blue, black, yellow, & green w/yellow strip. Can you provide me with correct color splicing conections.
1 Answer Hello Norm. Due to the lack of a wiring diagram, we would have to recommend you purchase the wire harness for the ice maker WPD7813010 for safety reasons. Thanks! Read More...
Norm S. May 13, 2011 for Model Number model # thi21s3w MFG# p1194704ww & ser# 9503150904 Ice maker will not work. Plugin will not fit my fridge. I will splice it to make it work. Can you provide the wiring diagram for the 4 wires to hook up my icemaker. The wires are different colors ----same amount of wires.
1 Answer Hello Norm. Have you tried to remove the old plug harness from your old icemaker to use on the new icemaker? To make the removal of the existing wiring harness easy, you can start by removing the white cover off the old icemaker. You will see the tab that holds the connector in, press it in to release the harness and reinsert it to your new icemaker. Hope this helps! Read More...