Scott September 30, 2020 for Model Number WGD9500TW2 When the dryer is off, we smell gas. Not a lot, but over time it builds. I've replaced the gas line and valve from the wall, and used yellow teflon tape on all the fittings and confirmed with soapy water there is no gas leak from the wall into the dryer. Our old dryer didn't have this problem, however we just replaced it with this one, however the current dryer sat in storage for 7 years, and is now being used. Is there a part inside the dryer that may be leaking allowing the gas smell when it sits idle?
1 Answer Scott, as the gas supply line has been verified as not having a leak, the only other location that gas can come from would be from a sticking gas valve WPW10118347. Read More...
Thomas April 21, 2015 for Model Number mgdb725bw0 OK I am going to ng from lp what order is the spring and limiter installed in on a maytag bravo xl.
1 Answer Thomas, Yes to go from LP to Nat you will need to install the following parts natural gas spring WP694422, Natural gas regulator WP694423, natural gas limiter WP694424, and burner orifice WP15418 Read More...
Jandrh232 March 21, 2015 for Model Number GGW9200LT1 Converted from lp to ng with orifice 42 and limiter cap. Burner assembly diagram show spring and regulator also. Would those have been removed when previously converted to lp (different owner)? If they were removed and I just have the limitor cap installed, what is that doing? What do they do specifically?
1 Answer Jandrh, The spring WP694422 and regulator WP694423 maintain a predetermined amount of pressure on the regulator diaphragm, they must be installed when the dryer operates on Nat. Gas. The limiter / cap WP694424 Holds everything in position, and also works as a vent, should there be a pressure increase or fluctuation that could damage the valve interior components. Read More...
Leah February 06, 2015 for Model Number RGX5634KQ3 What parts are needed to return dryer from Propane to Natural Gas?
1 Answer Leah, to convert the unit back to NG you'll need the orifice WP234826, limiter WP694424, regulator screw WP694423, and spring WP694422. Thanks. Read More...
Garcia November 30, 2014 for Model Number WGD6400SW1 What parts required to convert dryer back to natural gas from lp?
1 Answer Garcia, to convert the unit back to NG you'll need the orifice WP234826, limiter WP694424, regulator screw WP694423, and spring WP694422. Thanks. Read More...
Tom October 22, 2014 for Model Number duet dryer gas ggw 9250 pw1 Changing dryer back to natural gas how do you determine the proper setting the regulator adjustment part # 694423
1 Answer Tom, This is preset from the factory, you just put the part in place and put the nut back on. Read More...
Jon M October 21, 2014 for Model Number Roper RGX5636A I am not getting any gas out. The ignighter glows bright red, but I don't hear the valve open. So then the ignighter is de-energized, and the tub just keeps turning with no heat. Could this be caused by a bad regulator? It's natural gas. I checked that white fuse in the back with a meter, and it is good. Also, on the auto dry setting, it just keeps running, probably because of the no-heat situation. thank you!
1 Answer Hello Jon. You will need to order and replace the gas valve 279923 on the unit. Read More...
Dean October 09, 2014 for Model Number Kenmore 110 7790 2792 What parts are needed to convert back from LP to natural gas? Cannot locate original parts.
Shawn September 16, 2014 for Model Number LGR7646EQ0 I need to switch this back to NG from LP and I need to know what parts I need for the NG conversion. Thank you.
1 Answer Shawn, to convert the unit back to NG you'll need the orifice WP234826, limiter WP694424, regulator screw WP694423, and spring WP694422. Thanks. Read More...
Mike May 17, 2014 for Model Number wgd6600vw1 I have this dryer and it was converted to LP gas now I need to convert it back to natural gas. What parts will I need?
1 Answer Mike, to convert the unit back to NG you'll need part numbers WP694424, WP694423, WP694422, and WP234826. Thanks! Read More...