Jeff L. October 09, 2013 for Model Number GS6NVEXSL01 We need to purchase a pan slide for this refrigerator appliance. Do you have it and what would it cost?
1 Answer Jeff, according to the model number supplied the pan slide is part number WP2223320. This can be used as the left or right hand side. Thanks! Read More...
Joe September 15, 2013 for Model Number Whirlpool GS6NBEXRSO01 Pan slides broke on our snack drawer of our refrigerator, need to confirm that Part Number: AP3180471 Made by: Whirlpool is the correct pan slides for our refrigerator. Thanks.
1 Answer Joe, I've found model number GS6NBEXRS01. Yes, the slide pan WP2223320 is the correct replacement listed for your model. Thanks! Read More...
Pam July 25, 2013 How do I remove the broken pan slider and replace the new one on my whirlpool fridge? The pan slider is model no. AP3180471. Thank you.
1 Answer Hello Pam. There are two locking tabs on the slides. You release the tabs and the slides will slide toward the front and out of the unit. Read More...
1 Answer Make sure the freezer is between 0° and 5°. You need to check and see if there is power going to the water valve when the icemaker cycles. If so, replace the water valve on the unit. If not, or the icemaker does not cycle, you will need to replace the icemaker on the unit. Also, check and make sure the fill tube on the unit is not frozen and clogged. If so, replace the water valve and thaw out the fill tube. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Richard B May 16, 2013 for Model Number CSF20EBU There are two pans that pull out at the bottom of the bottom of the refrigerator. They both use the same square aluminum grab bars. It should have plastic end caps. The end caps have gone missing allowing the metal to make contact with the sides of the unit. This is scratching the finish when the drawers are moved in and out. I cannot find replacement end caps in the diagrams. Please advise.
1 Answer Richard, The endcaps for the handles on the crisper drawers have been discontinued by the manufacturer with not replacement. Read More...
Jerry April 16, 2013 for Model Number Whirlpool Refrigerator Model GS6SHAXMQ00 This seems to be a frequent problem. One of the Pan Slides for the Snack Drawer on my Whirlpool fridge broke. I ordered and just received the replacement Pan Slide part #A318471 (Whirlpool no. 2223320). It appears to be the correct part, but, as others have observed this part now contains 2 small, round protrusions approximately a quarter inch in diameter and sticking out about an eighth of an inch that prevent the slide from fitting flush against the bracket. These protrusions are at each end of the Plan Slide and they prevent the 3 L-shaped tabs from sliding into the slots on the support bracket. I note that you advised another questioner (Dave) to cut the protrusions off. What do you suggest we use to cut these plastic "dots" off a $12.95 part without breaking the part (or injuring ourselves)?
1 Answer Jerry, You can try to remove the tabs using side cutters or something like that in order to get the slid on. This is the way the manufacturer is designing and you would have to find a way to clip then off. Read More...
Ellen April 13, 2013 for Model Number ED2VHEXVBO1 I have a crisper drawer that has broken. I also need the pan slides. I want to know if part AP3596370 is the correct part for the replacement drawer and what pan slide do I need to order to correspond with the drawer so I order the right part.
1 Answer Ellen, The part number for the crisper pan for your unit is WP2188656 and the slides would be the crisper shelf W10508993 Read More...
Rita Y. April 05, 2013 for Model Number GS5SHAXNLOO I just sent a request about putting in a drawers slide for the crisper, and there are 2 small plastic dot protrusions one on each inner end that prevent the slotets from being engaged...do we remove these? how? we seem to have the right part as we have checked multiple web sites and all pointed to that popular part...the earlier email did not have that whirlpool model number...
1 Answer Rita, The "lower" crispers (meat pan and vegetable bin) pan sldes are molded into the cover or frame, and will require the repalcement of that part. The upper "crisper drawer(snack tray) pan slides attach to the metal frame of the shelf, then the pan slides into the pan slide. Could you re check which pan or drawer we are dealing with, and an e mail address so we can duscuss this further, if needed. Read More...
Rita Y April 05, 2013 for Model Number whirl;pool sx.. I am pretty sure we have the right replacement parts for the drawer slides in our side by side...checked on multiple sites...but there are 2 smalls pklastic dots one on each end that stop the brackets from engaging...what should my husband do? and if we need to remove those, how?
1 Answer Rita, Check the shelf frame there should be corresponding openings or tabs in it to secure the WP2223320 pan slide to the shelf, to keep it in alignment, then the shelf will slip into the tracks of the pan slides. Read More...
Suel March 12, 2013 for Model Number 2223320 just got a replacement slide 2223320 but it says it is cav#1, and i need #2. how do i get the right model? the model #1 has some protrusions on either end that wont allow the slide to be flush with the frame, and so it wont fit the frame properly.
1 Answer Suel, We will need the model number for the unit to assist with getting the correct part.Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...