Db November 18, 2022 for Model Number MGR5730BDW Where is the cook top ignitor module located on this stove?
1 Answer DB, Thanks for the question!!! You would find it on the back of the stove or under the cooktop. Read More...
Gary October 29, 2022 for Model Number Maytag #MGS5775BDS Igniters for burners would not ignite. Had to use a lighter to use the range top. Would like to service myself, not sure of the needed part. Would appreciate the input.
1 Answer This could be caused by a switch harness 74010915 or the spark module 8215557. You can test the harness for continuity when in the light position. Read More...
Joeseph October 12, 2022 for Model Number JGD8130ADS Where is the Spark Module located on this model.
1 Answer Joseph, Based on the model provided the spark mod looks to be located in the plenum housing under the main cooktop body. Read More...
John B. February 19, 2022 for Model Number JDS9860AAP Burners will not light except manually with a flame. Purchased and replaced spark module but nothing changed. Spark module has 120 VAC when each burner is in the light position. Checked for short to ground on all wiring from the spark module to the igniters and found none. Igniters spark normally when one or both burners on each side are lit and the knob is in the light position. Removed the burners from the pan and cleaned out the crud but still no change. Any further suggestions?
1 Answer Hello John, If there is 120Vac to the spark module and gas from the valve, the issue is either a poor ground to the surface burners or the burners WP3403M075-10 are in need of replacement. Read More...
John February 17, 2022 for Model Number JDS9860AAP All burners will not light except with a flame. Purchased and replaced spark module but no change. Module has 120 VAC with each burner in the light position so the knob switches seem OK. Any Ideas?
1 Answer Hello John, based on the description and the part replaced follow the spark wires from the spark module to the burner module ignitor receptacle, likely there is a short to ground there, also the burner modules can be taken apart and the internal spark wires checked. Read More...
John February 14, 2022 for Model Number JDS9860AAP Where is the spark module located for this Jenn-Air gas cook top. All 4 burners will not light except manually with a flame.
1 Answer John, the spark module 12001596 is located at the bottom back of the appliance and would be accessed by moving the range out. The lower access panel would then be removed to expose the module. Unplugging the power cord and turning the gas supply off before replacement would be recommended. Read More...
Andrew January 02, 2022 for Model Number 6157XUW Where is the spark module on Magic Chef gas range model 6157XUW? The four surface burners started getting more difficult each day to light up over a two weeks period. Today all four have stopped clicking to light up completely. I think the spark module needs replacement; but this is an old range and not sure where the spark module is located. Thanks.
1 Answer Andrew, Pull the unit out and remove the back cover and check to see if it is there and if it is not there then look in the storage drawer area. Read More...
Pete Lopez December 07, 2021 for Model Number Magic Chef 8351VD My Stove Top has 5 burners. Does Module 12001596 / AP4010034 have 5 terminals? Please advise. Thanks
1 Answer Pete, No, this spark module will only have 4 terminals on it. On your unit it is showing a 2 terminal spark module WP74004282 and a 4 terminal 8215557. Read More...
Jimmy November 29, 2021 for Model Number Magic Chef 8321TA cook top I can't ignite any of the burners. To start with it would still click but not light and then it quit clicking all together and have to light with match. What do you think the problem is?
1 Answer Jimmy, Make sure that the burners are clean and if they are then test the ignition switches to make sure that they are good for continuity in the light position. If this is good then the spark module would be the most likely cause. Read More...
1 Answer Hello Gerald, The spark module is located on the lower right side base rail as viewed from the front of the unit. Remove the top and side panel. Remove three screws from the rear and top edges of the side panel. This should loosen the side panel enough to pull up and disengage the "keyhole" at the front inside of the panel (top & bottom) from the screw and plastic spacer holding it in place. The spark module is mounted on a bracket on the base frame. Read More...