Carlos M August 07, 2017 for Model Number WFE320M0ES0 I have a Whirlpool Electric Range that the "Cooktop ON" idicator light stays on. It happened ever since a storm we had the other day we lost power then when it came back that light stays on. I have already tried powering down and waiting then power up again. What part do you recommend I change? I was thinking to just change the indicator light but the same thing will still happen won't it? Maybe replace a switch? Also is the range safe to use for now?
1 Answer Carlos, This issue would be caused by a faulty infinite switch. You can disconnect the purple wire from each switch and test from the terminal to chassis of the unit to see if there is 120 vac at the terminal. If there is then this would be the issue. Read More...
Keith October 30, 2015 for Model Number RF362LXTS The two large front burners cycle on and off frequently and don't appear to stay on long enough to heat the pan. What's Wrong?
1 Answer Hello Keith. It is normal for the elements to cycle on and off. If it is to much, replace the switch on the unit. Read More...
Mike October 27, 2014 Stovetop works perfect, oven clicks but doesn't heat up any ideas ? Not sure of model number
1 Answer Mike, You most likely have a DSI spark ignition system, since you can hear the oven igniter click you may have a weak or inoperative solenoid on the gas valve. It may look like this WPW10293048. Also check the wiring for loose connections and the oven gas valve flipper is in the open position(down). Read More...
Rob Z August 02, 2014 for Model Number RF262LXSQ0 The right front burner of our Whirlpool range is no longer functioning. For a long time the burner would run on high, no matter what heat temperature setting we had it on. Now it no longer works. I suspect the switch is at fault here, but I am not sure if I need an "infinite switch" or "surface switch". And your site says the switch you need to purchase depends on whether it is for a large or small "unit". Does it mean large or small "element?". Sorry for the multiple questions. Thanks in advanced for your help.
1 Answer Rob, You will want to inspect the burner for the unit for being burnt out. If this checks ok then you would need the infinite switch part number WP3149400 Read More...
Tulip March 31, 2014 for Model Number FEP310VQ I need the metal stub part only for my Roper stove. I see on the website there is a switch infinite board and according to the diagram that is the part I would need. I just needed to make sure that is the right part. Thanks
1 Answer Hello Tulip, The infinite switch for your unit is going to be dependent on whether the switch is for a large element WP3148953 or a small one WP3149404. Read More...
Steve February 02, 2014 for Model Number rx362lxsbo Hello, Just wondering if my whirlpool accubake part number is correct. The stove model # is rx362lxsbo. The switch that I pulled has part number 3148954. Everywhere I look, seems like the description for this part is for an 8 inch burner. My burner seems to be slightly larger than 8inch. All parts I see being suggested is 3149400. Is this right? It is for the front right single burner (the bigger one).
1 Answer Hello Steve! I believe your model should read RF362LXSB0. According to the model number supplied and the original part number given, the right front burner switch replacement is part number WP3149400. Thanks! Read More...
Benny April 10, 2013 for Model Number RF362LXTS 2 Hello my name is Benny, I have a Whirlpool Accubake oven model # RF362LXTS2. The front left big burner only works on high and only even if you try to set it on low and also it dosent work at all when set on dual. When in single it works like it should as dual but only at the highest setting. Could you let me know what the problem could be? Do I need to get a new burner or is it a switch that I could replace? Thanks for you help.
1 Answer Hello Benny, This sounds like you have a bad infinite switch WP9758060. This is the switch behind the control knob. Read More...
Leroy D. January 11, 2013 for Model Number WFE361LVQ O Ser.# ROO477870 I need the on off - tempeture control Switch for model range listed for the right front large burner. The unit that is out has part number 3148954. Thanks, Leroy
Bill December 22, 2011 for Model Number RF366PXXN2 My control switch is #3148952 and is marked 5.4 - 7.8A 240V. Will the AP3095448 part work for this?
1 Answer Hello Bill. No, based on the model and part number you provided, WP3148952 is the correct infinite switch. Hope this helps. Read More...