Moon M May 19, 2013 for Model Number Whirlpool top load Can't find model number, washer does not fill up completely regardless of setting Small, Medium or Large. Voltage from the pressure switch to the main control is good and also good connections and OHMs readings. Pressure switch clicks when I blow air to the switch and is opening and closing. I was sure it would be the pressure switch but not not so sure since it closes and opens when air is blown into it through the hose. Could the pressure switch still be bad? The pressure switch has three wires if that helps identify the model number. Found one in your listing but not 100% sure its correct. Anything else that might be causing the water not to fill up? It appears it only fills for small load regardless of setting.
1 Answer Moon, We would be unable to determine the correct pressure switch without a model number. You will want to make sure that the pressure hose is not kinked or clogged and make sure that the air dome is not clogged. You also will want to check to make sure that the screens on the water valve are not clogged. Read More...
Sam March 06, 2013 for Model Number wfw8410sw01 Whirlpool front load washer flashing F24. Does not do anything.
1 Answer Hello Sam. If the water temperature sensor (NTC) value is out of range (23°F to 217°F [-5°C to 103°C]) during the water-heating step of the WASH cycle. Possible Causes/Procedure - Unplug washer or disconnect power. - Check connections to water heater & CCU (TH2 & HE2 cavities) connectors are not broken or wires detached and connector internal pins are visible. - Check continuity from the water heater sensor (black wires) to CCU (TH2 cavity) connector. - If the continuity diagnosis failed the Main Harness must be replaced. - Check that the resistance of heating element. - Check that the resistance of the water sensor. - Plug in washer or reconnect power cord. - Verify the unit operation by running the Diagnostic Test cycle. - After the diagnostic test has finished, unplug washer or disconnect power and wait for 15 seconds. Read More...
Dan B December 22, 2012 for Model Number WFW8400TW03 Whirlpool Duet Sport WFW8400TW03 front loader washer. Getting F20 error code.Things I've done. 1) checked hot/cold fill hoses, good water pressure, no clogs, inlet value screens appear clear 2) checked water pressure switch, checked continuity per manual, ok 3) blew into water pressure switch, heard 2 clicks, ok 4) blew into water pressure hose, could hear bubbles and air going through 5) Tried Hot cycle, then cold cycle, got F20 on both, usually washer fills up with water ok and then get F20 code, sometimes, looks like it goes through wash cycle and then F20. 6) Don't see any kinks in hoses interal or external, looks like all electrial connectors are connected.
1 Answer Hello Dan, You will also want to check to make sure that the drain pump is operating. Make sure that there is not a siphoning effect happening where the water just flows back out of unit. Press Pause/Cancel to clear display and the unit will drain for 3 minutes. Verify that the harness connections to valves, pressure switch and control board are good. Check for leaks from hoses. Check the hose attached to bottom of tub to make sure that there is nothing clogged in it not allow water to drain properly. Read More...
Wendy J October 13, 2012 for Model Number WFW8300SW00 I put my machine on Quick Wash which is programmed for 28 and when it gets to 20 it stops and Sd shows. I can not do any cycles with it. I cancel the load and then try it again and it flashes F21. I can then cancel the load and do drain and spin and it goes through that 15 min cycle. I have tried all of the settings - gentle cyle, etc and it does the same thing. Please advise. Thanks
1 Answer Hello Wendy. Based on the error code and information you provided, it sounds like the water level switch W11417619 is bad and will need to be replaced. Read More...
Tiffany September 21, 2012 for Model Number mhwz600tk00 Where is this switch (AP4340286) located in my machine?
1 Answer Hello Tiffany, When you remove the main top of your machine, the pressure switch should be on the right side near the back of the machine. Read More...
Cathy March 17, 2012 for Model Number WFW9150WWOO Washer doesn't rotate. Goes through each cycle, until it pumps out from rinse cycle. Then flashes, f1 e2 error. Doesn't spin nor rotate through the wash or rinse cycle.Door stays locked. Cloths are soaked. Belt looks fine. Please help.
1 Answer Hi Cathy. The F1E2 code is MOTOR CONTROL UNIT ERROR. The Motor Control Unit has internal failure. If failure occurs during high-speed spin, the door unlocks after 3 minutes.Possible Causes/Procedure - Verify the shipping system, including shipping bolts and spacers, are removed, and that power cord is out of the washer. - Check if washer is on a dedicated circuit. Other devices on same circuit can create line noise and cause this issue. - Unplug washer or disconnect power. - Check the neutral feed to the MCU and CCU from the AC line filter. - Make sure all wire harness connections between the Motor & MCU, and MCU to CCU, are not broken or with wires detached, and that connector internal pins are visible. - Make sure that all the connectors are fully seated. - Plug in washer or reconnect power. - Verify the washer operation by running the Diagnostic Test cycle. See page 5. - After the diagnostic test has finished, unplug washer or disconnect powerand wait for 15 seconds. Motor control unit part # WPW10384843. Thank You. Read More...
Frenchy November 05, 2011 for Model Number WFW8300SW05 Machine over fills ONLY during rinse cycle. Water fills almost 1/2 way up drum then starts leaking on floor from door, with or with out clothes. Wash cycle is fine. Did find cold water inlet screen slightly clogged with sediment but valve is holding when machine is off?
1 Answer Hi Frenchy. You will need to replace the unit pressure switch part # W11417619. Then as you are in there, blow back into the hose towards the tub. If you felt like there were any obstructions, you will need to clean the pump and hoses. Use affresh tablets monthly part # W10549845 to insure proper efficiency. Keep your entire vent and outside working properly so you are not rewashing lint that will clog the washer. Thank You. Read More...
Confused October 11, 2011 for Model Number mhwz400tq00 Low water level, clothes have dry spots, on various cycles, water temp. Is the water level switch the only thing that controls water level? Can it or the tube be cleaned, or is it best to replace? Thanks
1 Answer Hello Confused. Blow through the pressure hose W11252474 and make sure it is not clogged. If it is clear and the water valves are good, you will need to replace the pressure switch W11417619. Hope this helps. Read More...
Waldo September 15, 2011 for Model Number Wfw8410Swoo Getting a error code f21. I have changed the pump, cleaned the hose, and just changed the pressure switch and it still stop on the rinse cycle. Help.
1 Answer Hello Waldo. If the pump, hose, and the water level switch is new, you will need to test for power going to the pump assembly before the rinse cycle. If there is none there, you will need to replace the CCU WPW10679602. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Cindy September 10, 2011 for Model Number MHWZ600TB01 EPIC Z MAYTAG FRONTLOAD WASHER I am not seeing any error codes just the add garments and everything else goes on as normal, until I press start then I hear a double click from the backside of the washer and the door unlocks then the machine turns off - or it spins over once then unlocks the door and all lights stay on.There is still water in the washer and it will not drain either...... Do you have any instructions to install these parts? If so where can I get them? Which part do you think it could be if either? Could I be missing something to check?
1 Answer Hi Cindy. Start a new cycle by opening and closing the door to let the control board another load is received.Does the door lock light come on? The door latch switch is part # W11417619. Can you press pause / cancel and the machine should spin and drain? Use a shop vacuum to drain water. If the pressure switch is not satisfied then it will not allow any function. Part # is W11417619. Remove power. remove the 3- torx screws (T-15/20) from the back of the top. Slide the top rearward and up to remove. Then on the front RT. back corner is the pressure switch. Part # is W11417619. Remove the hose. Blow back into it towards the tub. Did you "feel" any obstruction removed as you were blowing? Lint restrictions (plugged vent system needing cleaning) or scum build up ? Washer magic is part #W10549845. Thank you. Read More...