Chris January 02, 2012 for Model Number 106.59262990 Ref. was freezing up. I replaced heater, still freezing up. What next?
1 Answer Hello Chris. Test the thermostat and see if it reads closed for continuity. If so, and the heater is new, you will need to replace the timer W10822278. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Rafael December 23, 2011 for Model Number RS25AGXNQ02 Recently, my refer has been running and it is louder than usual for I have noticed. The refer side did not feel as if was cooling properly .There was barely any airflow coming through the vent and then finally none(evap motor not runing I figured). I noticed that the freezer back panel was frosted over. Once I took the panel off plugged back in and evap motor was working and airflow was resuming. Defrosted the coils whcih were frosted over manually with hair dryer .Figured that was it problem solved Feezer and refer working fine.Last few days I have noticed that freezer back panel is a bit frosty . To me I haven't noticed if the fridge has turned off to defrost mode. It just sounds on all the time and a bit louder than usual. My wife says I'm losing it ,but a feeling tells me there is something not right. Please help with any suggestions to test out
1 Answer Hi Rafael. The process you are going through is a normal defrost issue. Normally the failure of the defrost thermostat part # WPW10225581, not closing as the defrost timer sends the 120 vac part # W10822278 to it . In The fresh food area at the top rt. side there is this defrost timer. With a large blade screwdriver you can advance this dial to the first heavy click to start the defrost cycle. At this point, did the timer send the 120 vac to the evaporator mounted defrost thermostat ? Was the graduations of the turning detents seem difficult to do ? It should turn positively easy. If not then this is a telltale sign of a defective part. If it does not send the voltage to the thermostat, it is bad. The thermostat has to close at 14° or below. If you test it with a ohm meter and a temperature gauge, then you can tell. If it does not close to send the voltage to the heater then defrost will not occur. Then you need to disconnect the evaporator heater and test for resistance between 8-11 ohms (approx.). If it is -open- it will not conduct heat. It is part # WP2323198. You can purchase a volt/ohm meter at the local hardware very cheap. Thank You. Read More...
Chris December 17, 2011 for Model Number kenmore 708525991 I got the defrost timer with no directions... I applied the flying lead to the pink #2 lead is this correct for this model?
1 Answer Hi Chris. No, your model needs the wire connected to the # 1 terminal so it is a continuous run application as the instructions imply. They are confusing. Most of the time 98% of units hook up to the black at the # 1 terminal. Great question ! Thank You. Read More...
Rr December 15, 2011 I have a used Amana Refrigerator older 23 cubic feet I have no model number, the Deforst timer is bad. It freezes upper and lower.. Where is the Timer located? So I can get the part number off the old one.
1 Answer Hello RR. The defrost timer W10822278 can be located behind the toe panel, in the compressor compartment, and in the control section. Without a model number, there is no way to tell you for sure. When you locate the timer, you will see the numbers by the terminals. As long as you find a timer with the same number pattern, and the same amount of cycle time, it will work in the unit. Hope this helps. Read More...
El34han December 13, 2011 for Model Number SS27AQXHW00 (Kirkland/Whirlpool) Bought a AP3110896 don't know where to connect the black wire. The old part# 2176648. Pin#2 PK, pin#1 OR, pin#4 R, pin#3 W Where should I connect the black wire on the new AP3110896? Thank you.
1 Answer Hello El34han. The black wire goes onto the number 2 terminal of the timer W10822278. Hope this helps. Read More...
Mike December 13, 2011 for Model Number Whirlpool ED226WXFW01 I have the replacement defrost timer #482493 however don't have schematic for the refrigerator available. What terminal does the black wire from the timer get connected to. Thanks in advance for any help.
1 Answer Hello Mike. The back wire goes onto terminal number 2 of the defrost timer W10822278. Hope this helps. Read More...
Craigo December 10, 2011 for Model Number sears coldspot 106.7635240 Installing d/frost timer kit AP3110896. Slightly confused by continuous vs. cumulative, old timer harness connecting to pins were two white on 3, red on 4, black on 1 and red on 2. I hooked the black lead coming from timer to pin 1. Correct? also when I plugged it in the compressor didn't kick on, so I had to rotate the timer til it clicked then it kicked on when I plugged it in. I cut and taped off the green wire that hooked on to the defective timer. Should I be good to go?
1 Answer Hi Craig. Yes the difference between all the explanations can be confusing. The black motor wire will generally always go on the # 1 terminal. You should be fine. This will give the defrost timer motor the 120 vac needed for proper operation by the timer. There are a bunch of 6-1/2 hrs of timer graduations as you rotate the timer knob. There are precise and simply tiny clicks. The defrost cycle will start when you advance the detentions at the first "Heavy Click". The defrost cycle will normally stay active for approx. 25 minutes and then at the "2 Heavy click" it stops the defrost and starts the compressor in the normal run time. 24 / 7 days a week. Thank You. Read More...
W Bingee December 07, 2011 for Model Number Kenmore 106 515 82200 frig Thank you for verifying that a version 2 cum defrost timer requires the black fly wire to be connected to terminal 1 on part 482493. One quick follow up: Am I correct that my Kenmore 106 515 82200 has a version 2 timer? I am 99% sure I read my schmatic correctly but I would feel much better if I could get another opinion. Thanks again for great support!
1 Answer Hello W. Bingee. Yes, based on the wiring colors you provided, the timer W10822278 should be version 2. Hope this helps. Read More...
Andrew December 07, 2011 for Model Number Whirlpool ED25VF Hi, I have a Whirlpool ED25VF refrigerator. Originally, the cooling system would turn off and not come back on. I replaced the defrost timer (part #482493), placing the black wire on the terminal labeled #1, where the orange wire is attached to also. Now the cooling system shuts off sometimes, but comes back on, and I find that sometimes items in the freezer are somewhat thawed. Could this be a thermostat or heater problem? Thanks
1 Answer Andrew, It sounds like you have wired your new timer as a cumulative version 2 / procedure 3 according to the instruction sheet. it actually sounds like the timer is working proper. But if the freezer is getting too warm in the defrost cycle, you need to consider the defrost thermostat WPW10225581, Check and make sure the thermostat has not gotten disloged from the panel it's mounted on and then replace it, it would most likely be hanging up and causing an over heat situation. Good Luck and Thanks Read More...
W Bingee December 06, 2011 for Model Number kenmore 106 515 82200 (Whirpool mfg) My defrost timer is noisy and since I only hear it when the compressor is on and when defrosting I suspect I have a cum compressor timer. Acording to my schematic and info I have researched I believe I have version 2. So I think I attach the black wire to terminal #1. Is this correct? Thanks so much...
1 Answer wBingie, Yes, correct, if you have a version 2 accumulative compressor defrost timer, you connect the loose black wire on the new timer to terminal #1, along with the black wire in the timer wire harness. Very good job. Thanks and Good Luck Read More...