Refrigerator Divider Or Deflector

The Door Mullion is an OEM part for GE refrigerators. It is a vertical component that separates the fresh food and freezer compartments, while allowing for the seal and closure of the refrigerator doors.

Causes of a bad door mullion may include physical damage from impact or mishandling, wear and tear over time, or compatibility issues with the specific refrigerator model.

Symptoms that may indicate a need to replace the door mullion include:

• Air leaks or drafts between the fresh food and freezer compartments
• Difficulty in closing or sealing the refrigerator doors properly
• Visible cracks, breaks, or damage to the mullion itself
• Condensation or frost buildup around the mullion area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

The Mullion (White) is an OEM part for GE refrigerators. This is the vertical strip that helps seal the space between the French doors, ensuring an airtight closure when the doors are shut. 

Causes of a bad mullion can include physical damage from impacts, wear and tear from regular use, or issues with the pivot or hinge mechanisms that allow it to fold and seal properly.  

Symptoms of a bad mullion include:

• Doors not closing properly
• Visible gaps between the French doors
• Increased condensation or frost buildup around the door edges
• Higher energy consumption due to inefficient sealing

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This ice dispenser deflector mounts in the freezer door chute to guide cubes or crushed ice into your glass. Replace a cracked or missing deflector to reduce scatter and keep ice flowing where you want it.

• Directs ice down the dispenser chute toward the glass
• Helps contain spray and bounce-back of cubes
• Restores proper flow when the original deflector is cracked, warped, or missing
• Common symptoms: ice misses the glass, ice scatters on the floor, visible damage to the deflector

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Access the dispenser area per your model's instructions and note the deflector's orientation
• Transfer any screws or clips from the old part; avoid forcing plastic tabs
• Restore power and test ice dispense to confirm proper direction and clearance

The Drawer Guide is an OEM part for LG refrigerators. This part allows the smooth and effortless operation of the refrigerator's drawers, ensuring they glide in and out with ease. 

Causes of a bad drawer guide can be attributed to wear and tear over time, misalignment during installation, or damage from excessive force or improper use of the drawers.

Symptoms of a bad drawer guide include:

• Difficulty opening or closing the drawers
• Drawers getting stuck or not sliding properly
• Excessive friction or resistance when operating the drawers
• Drawers becoming misaligned or tilted
• Unusual noises or grinding sounds when using the drawers

This OEM LG part is also compatible with some Kenmore models.

This is the vertical flipper mullion assembly that mounts to one fresh-food door and pivots closed to seal the center gap when both refrigerator doors are shut, helping maintain proper temperature and energy efficiency.

• Creates the center seal between French-door refrigerator doors
• Helps prevent warm air infiltration and moisture/condensation in the fresh-food section
• Common failure signs include a loose or broken hinge, mullion not staying aligned, condensation at the door center, or doors not sealing properly
• May also be noted if doors pop open or temperature fluctuates in the refrigerator compartment

• Unplug the refrigerator before servicing
• Remove door bins to access mounting screws/clips
• Transfer any original covers or hardware if not part of the new assembly
• Verify proper hinge engagement so the mullion flips and seals smoothly before restoring power

This divider guide kit replaces the guide components that support and align an adjustable divider inside the refrigerator. It restores smooth movement and secure positioning so the divider stays put and your bin or basket stays organized.

• Guides the adjustable divider along its track and keeps it centered
• Helps the divider hold position to partition storage space
• Replaces cracked, warped, or missing guide pieces
• Common symptoms: divider falls out, won't stay in place, binds, or is difficult to adjust; visible broken plastic on the guide

• Unplug the refrigerator and remove the affected bin/basket and divider before beginning
• Note the orientation and fastener locations to aid reassembly
• Use the appropriate screwdriver or nut driver; avoid overtightening into plastic
• After installation, the divider slides and locks securely

This is the flip-out center rail for French-door refrigerators. It closes the gap between the fresh food doors to maintain a tight seal, helping keep cold air in and moisture out for consistent cooling. What it does

• Flips into place when both doors close to complete the perimeter seal
• Helps prevent warm-air leaks and condensation between the doors
• Supports proper temperature by reducing air infiltration
• Common symptoms: loose or broken flipper, doors not staying closed, moisture or frost at the center seam

• Includes 1 door mullion (flipper) assembly

• Disconnect power before servicing and clear items from door bins
• Open the doors and carefully release any retaining screws/clips; design varies by model
• Note spring orientation/hinge engagement and transfer any trim as needed
• Ensure the flipper moves freely and snaps closed before restoring power

Color: Black

This mullion assembly forms the front center divider of the refrigerator and includes an integrated anti-sweat heater. It helps keep the area where the door gaskets meet dry, supporting a clean look and a reliable, moisture-free seal.

• Provides the rigid center divider that the door gaskets seal against
• Built-in heater warms the divider to reduce sweating/condensation in humid conditions
• Helps limit air leaks that can lead to moisture, frost, or temperature fluctuations
• Common signs of trouble: persistent condensation on the center divider, visible cracks/warping, or poor gasket contact along the center

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Remove mounting fasteners, carefully release the assembly, and disconnect the wire harness (note routing/orientation)
• Position the new assembly, reconnect the harness securely, and reinstall fasteners without overtightening
• Verify doors close smoothly and gaskets contact evenly along the divider before restoring power

This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.

• Guides the icemaker fill stream into the fill cup/funnel during the fill cycle
• Diverts stray or excess water to the overflow path to reduce spills
• Helps prevent leaks, sheets of ice, and clumped cubes under the icemaker
• Clues it may be needed: cracked, warped, or missing guide; water dripping from the fill area

• Disconnect power and turn off the water supply before servicing
• Remove ice bin and any covers to access the icemaker fill area
• Unclip/unscrew the old diverter; align and secure the new part to the fill cup/tube
• Restore water and power; run a test fill and check for leaks

This air diverter is a duct component that directs and balances airflow inside the refrigerator. Replacing a cracked or missing diverter helps restore proper cooling performance and reduce frost or condensation around air passages.

• Guides cold air from the evaporator through the intended duct path
• Helps maintain even temperatures between compartments
• Improves airflow seal and direction to reduce warm-air bypass
• Common symptoms: uneven cooling, weak airflow, frost/condensation near ducts, or visible damage to the diverter

• Disconnect power before servicing
• Remove shelves/drawers and the interior panel to access the diverter per your model's service information
• Note orientation and transfer any reusable screws/clips
• Do not overtighten fasteners into plastic; confirm unobstructed airflow before restoring power

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

Replacement diverter overflow that helps channel excess water away from the ice maker/water system to reduce pooling and leaks. Restores proper drainage so the refrigerator interior stays dry and operates as intended. What it does:

• Directs overflow or stray water from the ice maker/water area into the drain path
• Helps prevent water pooling or dripping inside the freezer or cabinet
• Use when you notice leaks, water pooling under shelves, or water coming from the dispenser/ice area

• Always disconnect power and shut off the water supply before starting any repair
• Removal of interior shelves/trim or access panels may be required to reach the diverter
• Handle plastic tabs and clips carefully to avoid breakage; replace any damaged fasteners

This refrigerator deflector is a molded guide that mounts inside the unit to direct internal airflow where it's needed. Replacing a cracked, warped, or missing deflector helps restore proper circulation for more consistent temperatures and performance.

• Channels airflow within the freezer/dispenser path to maintain even cooling
• Helps reduce frost or ice buildup caused by misdirected air
• Can address symptoms like warm spots, frost around vents, or rattling from loose parts
• Replace if broken, deformed, or missing

• Disconnect power before servicing
• Remove shelves/panels as needed to access the mounting location; keep track of screws/clips
• Install the new deflector in the same orientation; reuse existing hardware
• Reassemble and verify that vents/air passages are unobstructed

The Mullion Rail is an OEM part for Bosch refrigerators. This part maintains an effective seal on the refrigerator door, helping to keep cold air inside and ensuring energy efficiency. The mullion rail folds when the door is opened and extends to create a tight seal when the door is closed, preventing air leakage and maintaining consistent internal temperatures.

Causes of a bad Mullion Rail can include wear and tear from frequent use, mechanical damage from forceful handling of the refrigerator door, or degradation of the rubber seals that can compromise its effectiveness.

Symptoms of a failing Mullion Rail include:

• Difficulty in closing the refrigerator door fully.
• Noticeable gaps or looseness around the door seal area.
• Increased condensation or frost buildup near the door edges.
• Escaping cold air from the refrigerator, leading to increased energy usage.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement cover frame that restores the appearance around the appliance control area while protecting internal components. Use it to replace cracked, warped, or missing trim and keep the control panel edges aligned and secure. What it does:

• Replaces damaged or cracked trim around the control panel for a finished, uniform look
• Protects underlying switches and electronics from dust and light debris
• Helps keep control-panel edges aligned and prevents loose or flopping trim
• Improves overall appliance appearance after impact or wear

• Disconnect power to the appliance before starting any repairs
• Removal of the control panel or console is typically required; keep all fasteners for reassembly
• Handle edges carefully to avoid scratches or cuts and to prevent damage to the new frame