Refrigerator Dispenser Parts

Well, I got online and found several YouTube videos on how to check what was happening. I have a multimeter and tools. I first replaced the external water filter just to make sure it wasn't that, and it needed it. That wasn't the problem. I then removed the water inlet valve which was really easy. I didn't disconnect the water lines but I did unplug the power plug. Using the ohms setting on the meter, I tested the coil of the valve solenoid. It wasn't open. I checked the voltage at the plug... Read more

• Door sweating
• Frost buildup
• Ice maker won't dispense ice
• Freezer not defrosting

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

• Ice maker won't dispense ice
• Door sweating
• Frost buildup

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

Unfortunately, this part isn't sold separately, but the plastic that is attached to the metal spring that allows the actuator to disengage broke and I had to physically pull the "paddle" part back up for the water to stop coming out. Easy removal with a square bit screwdriver. First, take off the trim piece underneath the LCD display (screws are underneath), then take out the screws for the LCD display and pull down and out, then unplug the wires. Then take the screws out of the actual part... Read more

• Ice maker dispenses too much ice

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

Replaced the ice dispenser module. Read more

I had started to order the part from GE at $34.95 + shipping when I did a search and found AppliancePartsPros.com. I was able to get the same part for half of the price of GE. I placed the order and actually to my surprise received the part the very next day. I watched the video provided on-line to see how to replace the part. It took me about 10 minutes and everything is working well. Beats paying a repairman to come out on their schedule and do the same thing at, I am sure, a much higher... Read more

• Door sweating

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

• Not dispensing water

Parts where perfect. piece of cake.my wife was very impressed. Read more

Shopped online and found your great website, read reviews and based diagnostics on similarities I saw in other peoples stories. So I was able to choose correctly when replacing the circuit board. As far as the water switch in door, and drawer parts I just replaced them because I was tired of gluing them, and knew that with everything working good again and looking good, that it would be like a Tune up for our refrigerator. Read more

Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

Finding the part was puzzling. AppliancePros had the relevant manufacturer's part schematics handy on-line through which I quickly identified and order the replacement part. But the best aspect was AppliancePros' Amazon-like excellence in a) pricing and b) swift delivery (with precious tracking included). Read more

Popped old one out easily and inserted new one. It is hard to tell from the product picture, but yes this part has the lever, face plate and rubber button included. Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more