Refrigerator Shaft Or Pin

Repair kit for refrigerator drawer slide mechanisms. Includes gears and rod to replace stripped, broken, or missing components in pull-out drawer rails.

Ice dispenser only making crushed ice instead of cubes? This solenoid valve kit fixes the cube/crushed ice selector. Easy DIY repair with video guide.

Replacement axle pin for refrigerator front caster wheels. Installs through wheel assembly to secure rolling casters. Needed when bent, broken, or worn.

Ice dispenser not working or making grinding noises? A worn auger drive bar often causes dispensing failures. Moderate DIY fix with video guidance.

Freezer drawer slide gear mounts behind the basket to guide smooth in-and-out movement. Replace if cracked, broken, or worn from regular use.

Ice maker clicking or not producing ice? A worn drive gear with stripped teeth is often the cause. This 5-minute fix restores normal ice production.

Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.

This is a small plastic wheel support or gear clip that attaches to the freezer drawer glide system. It helps the freezer drawer slide smoothly on its tracks by supporting the roller wheel mechanism. Replace this part if your freezer drawer is difficult to open or close, makes grinding noises, or sits unevenly on its rails.

Replacement bottom hinge pin for refrigerator doors. Restores proper door pivot and alignment when original pin is worn, bent, or missing during moves.

This joint assembly is the connector that joins two refrigerator water tubes to form a tight, leak-resistant seal. Replace it to stop leaks at a line coupling and restore reliable dispenser and icemaker water flow.

• Connects two plastic water lines within the refrigerator's water system
• Maintains a watertight seal to prevent drips and air intrusion
• Common fix for leaks at a coupling or tubing that won't stay seated
• Symptoms include slow/sputtering dispenser, small/no ice production, or visible seepage at the connector

• Unplug the refrigerator and shut off the water supply before servicing
• Dispense water to relieve line pressure
• Depress the connector collar to release the tubing; cut damaged tube ends square and fully insert tubing until it bottoms out
• Restore water and power, then check all connections for leaks

This replacement shaft is the mechanical link that transmits rotation and keeps aligned parts moving together inside your appliance. Replacing a worn or stripped shaft restores smooth, reliable operation of the connected mechanism. What it does:

• Transfers motor or gear torque to the mated component
• Maintains alignment and support within the assembly
• Helps ensure smooth engagement of gears, levers, or augers
• Common symptoms of a failed shaft: connected part won't turn or slips, intermittent operation, grinding/clicking noises, or visible wobble/play at the interface

• 1 shaft

• Disconnect power before servicing; shut off water supply if applicable
• Note the original orientation and take photos to aid reassembly
• Inspect mating gears/bushings for wear and replace if needed to prevent rapid re-failure
• Align any flats/splines and seat the shaft without forcing; tighten fasteners to manufacturer guidance

This is a small roller wheel or gear that supports and guides the freezer drawer as it slides in and out. It attaches to the drawer frame or track to allow smooth operation. Replace this part if the freezer drawer is difficult to open or close, makes grinding noises, or sits unevenly on its tracks.

Support bar for refrigerator freezer drawer assembly. Installs between roller tracks to stabilize drawer and prevent shifting. Replace if broken or missing.

This customized pin is a precision fastener that serves as a pivot or locating point within your appliance. It helps keep mating parts aligned and moving smoothly. Replace a bent, worn, or missing pin to restore proper operation. What it does

• Acts as a pivot/axle or locating pin between connected parts
• Maintains alignment to reduce wobble and uneven movement
• Supports smooth opening/closing or rotation at the joint
• Common signs it's needed: looseness, sagging or misalignment, scraping/squeaking at the pivot, or a visibly worn/bent/missing pin

• One customized pin

• Disconnect power (and shut off water supply, if applicable) before servicing
• Support the door/panel/assembly to remove load from the pin during removal/installation
• Note the orientation and order of any spacers, bushings, or washers and transfer them to the new pin
• Apply a light lubricant and verify smooth movement before restoring power

A small pin that secures the wheels or rollers on the bottom of a refrigerator, keeping them locked in position during normal use. It holds the roller assembly together so the appliance can be moved smoothly without the wheels falling apart. Replace this part if a roller keeps falling off or the refrigerator is difficult to roll when you need to reposition it.

Replacement pivot that supports and aligns refrigerator doors or drawers. Needed when original pivot is cracked, broken, or worn, causing misalignment.