Parts for Kitchenaid KFIS27CXBL3: 04 - Refrigerator Door Parts

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

This vertical mullion assembly is the interior trim piece that finishes and seals the refrigerator door edge, helping direct airflow and improve the door seal. It replaces worn or cracked mullion trim to restore fit and appearance. What it does:

• Provides the finished vertical trim on the refrigerator door edge and helps maintain an even door seal
• Channels cold air and helps reduce drafts that can cause temperature fluctuations
• Hides and protects the door edge and mounting hardware from wear and damage
• Restores proper door alignment where a damaged mullion causes poor sealing or visible gaps

• Disconnect power to the appliance before beginning any repair
• Remove door trim/panels per manufacturer instructions to access mullion; keep fasteners organized
• Align the mullion and engage all clips/tabs before re-securing screws or trim pieces
• If the door gasket or mounting clips are damaged, inspect and replace as needed for a complete seal

This mullion rail installs between refrigerator compartments to create a tight seal when the door closes. Replace if cracked, broken, or no longer sealing properly.

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

Seals refrigerator door to prevent air leaks and maintain temperature. Replace when torn, cracked, or loose. Confirm fit with your model number.

Seals refrigerator door to keep cool air in and prevent condensation. Replace if cracked, moldy, or not sealing properly. Verify fit with model number.

Replacement handle for refrigerator doors. Installs on refrigerator or freezer compartments. Replace if cracked, broken, or damaged during transport.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

White door stop that limits how far your refrigerator door swings open. Replace if broken, cracked, or missing to prevent door overextension and damage.

Color: White

Color: Black

Black plastic cam that the refrigerator door rides on to open and close smoothly. Replace if cracked, worn, or broken causing door misalignment issues.

White plastic door closure cam installs at the bottom hinge of your refrigerator door. Replace if cracked, worn, or broken to restore proper alignment.

The Door Handle Mounting Screw is an OEM part for Whirlpool refrigerators. It secures the door handle to the refrigerator door.

Causes of a bad door handle mounting screw can include wear and tear over time, improper installation, or excessive force applied to the handle. These factors can result in a loose or wobbly handle, compromising the functionality and aesthetics of your refrigerator.

Symptoms of a bad door handle mounting screw may include:

• A loose or unstable handle
• Difficulty in opening or closing the refrigerator door
• The handle becoming detached

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

6 - 19 x .250

This is an electronic control board that manages key refrigerator functions such as temperature regulation, defrost cycles, and ice maker operation. It mounts inside the refrigerator housing and communicates with sensors and other components to maintain proper performance. Replace this board if your refrigerator displays erratic temperatures, fails to defrost, or shows error codes on the display.

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal

Ice maker stopped making ice or won't turn off? This ice level control board monitors bin levels to control ice production. Simple DIY repair.

This headless, cup-point set screw secures a component to a shaft or hub inside your appliance. The 1/4-28 x 3/8 in size bites into the mating surface to prevent slipping, helping keep collars, pulleys, or knobs aligned and stable.

• Locks a hub, collar, or pulley to a shaft to prevent movement
• Helps maintain alignment and reduce wobble or vibration
• Replaces missing, stripped, or damaged set screws
• Common signs include components slipping on a shaft, rattling noises, or recurring loosening

• Disconnect power before servicing
• Clean threads and align with any flat on the shaft before tightening
• Start threads by hand to avoid cross-threading; tighten securely without overtightening
• Recheck tightness after a brief test run