Parts for Kitchenaid KBLS22EVMS2: 02 - Refrigerator Liner Parts

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

This housing is the replacement outer tub housing that supports and secures the washer tub and related drive components for proper alignment and operation. Restores stable drum mounting and reduces abnormal motion. What it does:

• Supports the washer's tub/drum assembly so the drum spins smoothly and stays aligned
• Provides a mounting surface for suspension and drive components to reduce vibration and noise
• Helps prevent rubbing or scraping by keeping internal components correctly positioned
• Commonly replaced when the tub feels loose, spins unevenly, or makes unusual noises

• One housing

• Disconnect power to the appliance before beginning any repair
• Handle with care to avoid damaging seals, sensors, or surrounding trim pieces
• Verify correct orientation and torque for fasteners; follow OEM service manual steps

This user interface control board sits behind the dishwasher's control panel, reading button presses and lighting indicators while communicating with the main control. Replacing a failed UI board can restore responsive controls and proper cycle selection. What it does:

• Interprets keypad/touchpad inputs and sends selections to the main control
• Powers and manages console indicator lights
• Common failure symptoms include an unresponsive or intermittent control panel, no indicator lights, or a unit that won't start or accept selections

• Disconnect power at the breaker before service and use ESD precautions; handle the board by its edges
• Access the UI by removing the console/inner door as directed in the tech sheet
• Transfer and fully seat the ribbon cable and wire harnesses; reuse mounting hardware as required
• After reassembly, restore power and run keypad/diagnostic checks per the unit's tech sheet, if applicable

Refrigerator light won't turn off or on? The door switch detects when the door opens and closes. Easy 5-minute DIY repair with a pick tool or scraper.

Replaces cracked or broken refrigerator light covers. Protects bulb and shields components from moisture. Slides into place with mounting tabs. Verify fit.

Left side housing cover for refrigerators. Replaces cracked, broken, or missing housings. Installs on the left side to restore appearance and protection.

Original Whirlpool light bulb, 40 watt.

Symptoms of needing to replace the light bulb include:

• Dimming or flickering light
• Complete lack of illumination inside the appliance
• Visible signs of damage or burnout on the bulb itself

Causes of a faulty light bulb can include normal burnout over time, electrical issues, or physical damage due to impact or vibrations.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Kenmore, Frigidaire, GE, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances.

Freezer or fridge light not working even with a new bulb? This light socket provides the electrical connection. Basic DIY repair with video guide.

Plastic insert that seats inside the refrigerator air damper cover to guide airflow from freezer to fresh food. Replace when cracked, broken, or missing.

Plastic cover that protects and supports the damper assembly in your refrigerator. Replace if cracked, broken, or missing to keep airflow components secure.

Reduces heat transfer in your refrigerator cabinet for efficient cooling and less frost buildup. Replace if damaged or deteriorated. Verify fit by model.

Refrigerator making clicking or knocking noises? A faulty damper control causes noise and uneven cooling. Easy DIY repair—remove cover, swap unit in minutes.

Secures your refrigerator's water filter in place for proper filtration. Replace if cracked, chipped, or filter won't stay locked. Confirm fit by model number.

Water filter head connects your filter to deliver clean water to the dispenser and ice maker. Replace if leaking or water flow is slow. Verify fit.

Replace your refrigerator water filter every 6 months to ensure clean, fresh-tasting water and ice. Easy twist-on installation. Verify fit with your model.

Protective cover that secures and encloses the water filter in your refrigerator's interior. Replace if cracked, broken, or tabs are damaged.

Secure mounting clip for refrigerator interior components. Replaces broken, cracked, or missing clips that hold shelves, drawers, or panels in place.

Restores the outer housing on your refrigerator. Replaces a cracked, broken, or missing cover panel. Shields internal components from dust and debris.

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

Fix drawers that stick, bind, or won't close properly. This slide guide realigns freezer and fridge drawers for smooth operation. Simple replacement.

Secures refrigerator water tube to cabinet, preventing shifting and rubbing. Replace if cracked or loose. Verify fit with your model number.

Dispenser facade cracked or discolored? This trim assembly restores your refrigerator's dispenser appearance and proper fit. Straightforward install.

Connects water line sections in your refrigerator. Replace if cracked, leaking, or damaged to restore secure connections to ice maker and dispenser.

Bypass cap replaces water filter when filtration isn't needed. Install when using RO system or preferring unfiltered water. Confirm fit with your model.

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles