Parts for Kitchenaid KRFC704FSS02: Refrigerator Liner Parts

The Water Filter Housing is an OEM part for Whirlpool refrigerators. It is the plastic housing that holds the refrigerator's water filtration cartridge in place within the unit. The housing ensures that water flows through the filtration cartridge as intended before being dispensed through the refrigerator door.

Causes of a bad housing can include cracks, leaks, or damage that compromise its ability to properly contain the filtration cartridge. Mineral buildup over time may also cause issues.

Symptoms of a bad housing include:

• Water not flowing through the dispenser
• Leaks around the water filter area
• Mineral deposits near the housing
• An ill-fitting or loose filtration cartridge

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This water tube routes water between the household supply and your appliance's dispenser or ice maker so water flows where it's needed. Replacing a damaged tube restores reliable water delivery and helps prevent leaks. What it does:

• Carries water from the inlet to the dispenser or ice maker assembly
• Prevents leaks when intact; cracks or holes can cause visible drips or puddles
• Supports proper filling of the ice maker and dispensing functions
• Can become brittle or clogged over time, interrupting water flow

• One water tube

• Shut off the household water supply and unplug the appliance before starting
• Inspect and replace any worn clamps or seals when installing the tube
• Route the tube along the original path and check for kinks that could restrict flow
• After installation, restore power and water, then check carefully for leaks

The Air Tower is an OEM part for Whirlpool refrigerators. It helps regulate and distribute cold air throughout the refrigerator. It circulates cold air from the freezer to the refrigerator compartment, maintaining a consistent temperature for your food. 

A bad air tower can occur due to blockages, damage, or wear and tear over time. If you notice symptoms such as uneven cooling, warm spots, or excessive frost buildup in the refrigerator, it may be time to replace the air tower.

Symptoms of a bad air tower include:

• Uneven cooling in the refrigerator
• Warm spots in the refrigerator compartment
• Excessive frost buildup

Restore your refrigerator by replacing the faulty or worn-out air tower with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Whirlpool EveryDrop Ice and Water Refrigerator Filter 2 is an OEM replacement part for Whirlpool refrigerators. This advanced water filter is designed to provide superior filtration for both the ice maker and water dispenser. This water filter effectively reduces numerous contaminants, including lead, pesticides, and pharmaceuticals, ensuring that your drinking water and ice are not only clean but also taste great.  

Regular replacement of the EveryDrop Filter is recommended to maintain optimal performance and water quality. Over time, filters can become clogged with particles and contaminants, leading to reduced water flow and a decline in the effectiveness of filtration.

Symptoms of a filter that needs to be replaced include:

• Noticeable decrease in water flow rate from the dispenser
• Unpleasant taste or odor in the water and ice
• The filter indicator light on the refrigerator turns on

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The FreshFlow Refrigerator Air Filter is an OEM component for Whirlpool and Maytag refrigerators. Located inside the ventilation system, this filter purifies circulated air. This air filter is 3" wide by 2" high and white in color. It should be replaced every 6 months to ensure the best performance.

Causes of failure relate to clogging from trapped dust, dander and other allergens despite regular replacement intervals. Performance decreases as filter media becomes saturated over months of use.  

Symptoms of a dirty or blocked refrigerator air filter include:

• Reduced airflow causes higher compressor runtime hours  
• Odors being pulled into the fridge from unfiltered vents  
• Shortening of food storage life due to unpurified air exposure
• Reduced fan speeds or strange noises originating from the vents

This genuine Whirlpool filter is also compatible with Maytag, Jenn-Air, and Amana models as well.

The Bracket is an OEM part for Whirlpool refrigerators. It securely holds the water filter in place, ensuring a tight seal and proper filtration of your refrigerator's water supply.

A bad water filter bracket can occur due to wear and tear, damage, or improper installation. If you notice symptoms such as a loose or misaligned water filter, water leakage around the filter area, or a decrease in water quality, it may be time to replace the water filter bracket.

Symptoms of a bad water filter bracket include:

• Loose or misaligned water filter
• Water leakage around the filter area
• Decrease in water quality or taste

Repair your refrigerator's water filtration system by replacing the faulty or damaged water filter bracket with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This electronic control board manages the appliance's functions and user interface, replacing a failed printed circuit board to restore normal cycle control and electronic operation. Fits as the direct replacement for the factory control module. What it does:

• Receives user inputs and sends commands to motors, valves, heaters, and sensors
• Manages timing and cycle selection so the appliance runs intended programs
• Can resolve symptoms like no display, unresponsive controls, cycles not starting, or erratic operation
• Interfaces with touchpads and led/lcd displays to show status and error codes

• Disconnect power before servicing to avoid shock or damage
• Handle the board by the edges and avoid static discharge; use ESD protection if available
• Transfer any user interfaces or harnesses exactly as removed; verify connector seating

The Filter Cap is an OEM part for Whirlpool refrigerators. It seals the water filter housing chamber located inside the refrigerator. The cap plays an important role in properly securing the water filter cartridge and ensuring a tight seal that prevents leaks.

Causes of a bad filter cap can include cracks, deformities, or warping of the cap due to pressure fluctuations over time within the filter housing chamber. 

Symptoms of a bad filter cap include:

• Water leaks from around the filter area  
• Inability to securely lock the filter cartridge in place
• Premature wasting of water when the filter is not fully engaged

This Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness routes power and signals between a dryer's control and components for reliable operation. It replaces damaged or frayed wiring to restore proper electrical connections and help eliminate intermittent faults. What it does

• Provides the factory wiring connections between control, motor, heating and safety components
• Restores lost or intermittent power caused by broken, burned, or corroded wires/connectors
• Prevents arcing and shorts when old wiring shows visible damage
• Ensures correct signal routing for controls and safety switches

• One complete wire harness assembly as shown

• Always disconnect power (unplug or shut off breaker) before starting service
• Route harness away from sharp edges and heat sources; secure with existing clips or ties
• Replace terminals or connectors that are melted or damaged to avoid future failures

This heater is the dryer heating element assembly that warms air used to dry clothes, restoring normal drying performance when the original element fails. Designed to replace a worn or broken dryer heater. What it does:

• Heats air circulated through the drum so laundry dries efficiently
• Replaces a burnt-out or open heating element that causes no-heat or reduced-heat symptoms
• Helps resolve long dry times or loads that remain damp after a full cycle
• Works with the dryer's thermal cutoff and thermostat to maintain operating temperature

• Disconnect power to the appliance before attempting service to avoid shock or injury
• Handle the element gently to avoid bending or damaging heating coils
• If other temperature-safety parts (thermal fuses/thermostats) show damage, inspect and replace as needed

This replacement sleeve is a small plastic insert that protects and guides a rotating or sliding shaft on the appliance, helping restore smooth movement and reduce wear. It's a simple, low-cost part that prevents metal-on-metal contact. What it does:

• Guides and centers a shaft or pin to keep moving parts aligned
• Protects metal components from wear and abrasion
• Reduces noise and vibration caused by loose or worn interfaces
• Helps restore proper movement when sleeves are cracked, split, or excessively worn

• One replacement sleeve

• Disconnect power (and water, if applicable) before starting any repair
• Remove surrounding components as needed to access the sleeve; use basic hand tools
• Inspect mating parts and replace or clean if damaged; do not force a damaged sleeve into place

The Heater is an OEM part for Whirlpool refrigerators. Responsible for maintaining optimal interior temperatures, it works to prevent cold air from accumulating at the bottom of the fridge compartment. 

Causes of a bad fridge heater include damage to heating elements over time, cracks in the casing, or electrical failures that impact the regulation of temperature. 

Symptoms of a bad heater include:

• Inconsistent or fluctuating fridge temperatures 
• Frozen items defrosting or thawing
• Heavy frost or ice buildup inside the fridge
• Food spoiling quicker than expected

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Refrigerator Temperature Sensor is an OEM replacement part for Whirlpool refrigerators. It is a crucial component responsible for accurately monitoring and regulating the temperature inside the refrigerator and freezer compartments.

Symptoms of a faulty temperature sensor include:

• Inconsistent or fluctuating temperatures in the refrigerator or freezer
• The refrigerator running continuously or not cooling properly
• Error codes or indicators related to temperature control issues

Causes of a bad temperature sensor can include normal wear and tear over time, electrical malfunctions, sensor failure, or damage from moisture or condensation.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.