Remington Tiller Parts

This genuine OEM replacement part is an extension spring for a Craftsman snowblower idler pulley assembly. The idler pulley attaches to a part of the snowblower's housing and is helps to transfer energy throughout the belt drive. This extension spring helps to redistribute some of the back-and-forth motion created in the pulley as the snowblower runs. This keeps the assembly from shifting out of place and potentially slipping. This extension spring is attached at two points and, if pulled in both directions too far, can eventually lose some of its tension. When this happens, the idler assembly can begin to shake and even slip out of place. Replacing the extension spring is an easy job that will only require a socket wrench to remove the idler pulley. A pair of pliers may help to remove the spring from its clips. This part is only compatible with Craftsman snowblowers and is sourced from its original manufacturer. It ships individually and any additional parts needed will have to be purchased separately.

The purpose of the fuel nipple in a small engine is to clean the fuel before it reaches the carburetor. If the fuel is dirty, it could cause issues with the carburetor and other parts of the engine. If the engine misfires, has a fuel odor, leaks, or has problems with dirty fuel getting into the carburetor, it may be time to replace the fuel nipple. It is an easy replacement, but be sure to work in a well-ventilated area. Drain the fuel tank and disconnect the spark plug before beginning this repair. This OEM fuel nipple is a genuine part right from the manufacturer. This fuel nipple can work well for snowblowers, snow throwers, chippers, tillers, and log splitters. It is compatible with a range of models from brands like Craftsman, Yard Machines, Yard-Man, MTD, and Troy-Bilt.

This air cleaner cover is designed to house the air filter on larger lawn equipment and other outdoor power tools. There is no aspect of small engine care more necessary than protecting the air that goes into the carburetor and cylinder from yard dust. Nothing is more incapacitating to a small engine than being clogged with dust, pollen, and other particulates that are invariably stirred up during landscaping work. While the air cleaner cover itself is not a moving part and would not seem to be subject to replacement, it is occasionally the case that, through extensive use or accidental contact, the cover becomes unable to shield the air filter within it. In these cases, it is essential to replace the cover with an OEM certified replacement cover that has been manufactured to the same specification as the original. Though replacing the cover itself is quite simple, it probably a very good idea to replace the air filters at the same time. If the cover is in need of replacement, it is quite likely the filters have been exposed to excessive amounts of particulate. This cover can be used on chippers, shredders, log splitter, mowers, and a variety of other small engine/large job equipment. Compatible brands include Troy-Bilt, MTD, Yard-Man, Yard Machines, and Cub Cadet.

Here is a replacement fuel tank for use with a range of different models of small engines. The fuel tank plays one of the most important roles in a machine with an internal combustion engine. The tank holds the gas, which flows through the fuel line, so the machine can operate. Although fuel tanks are durable and built to last, there could be any number of reasons that one may need to be replaced. On older machines, for example, the fuel tank could have become damaged or corroded. Even newer machines could have a faulty fuel tank that would need to have a replacement. If there is an issue with the tank, it is not a replacement that can wait. The tank could be leaking fuel, for example, which can be wasteful as well as dangerous. This genuine OEM replacement fuel tank is identical to the one that came with the machine. It is sold individually and does not include any of the hardware needed for replacement. It can work with dozens of models of tillers, log splitters, and other small engines. Compatible brands include Troy-Bilt, Cub Cadet, MTD, HUSKEE, MasterCut, and Yard Machines.

This spacer is a genuine MTD part that can be used as a replacement part for several different kinds of small engines, including lawn mowers, snowblowers, and wood-chippers. A spacer's function is to serve as a means to lengthen the distance between parts by fitting over a bolt or a screw to secure and maintain that distance. A reason to replace a spacer might be simply losing or misplacing the spacer itself, as it is small and can easily fall through cracks or unscrew itself over long periods of time. Other reasons include the gradual rusting, deterioration, bending, or cracking materials that can be attributed to general overuse or long-term exposure. If a spacer is subject to any of this kind of damage, it is best to replace it before using an appliance that requires a functioning spacer, as the malfunctioning spacer might cause permanent or serious damage. Always wear gloves when handling, repairing, and operating outdoor equipment. This spacer part is compatible with the brands MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually.

The fuel line is used to carry fuel through the machine, and it must be in good condition. As fuel line parts age, they are prone to damage. In some cases, they might crack, which could result in a fuel leak. Other times, the ends of the tube might not fit properly, even when they are clamped down. Eventually, the fuel line will need to be replaced. This is a relatively simple job, which will require only a pair of pliers to complete. This replacement fuel line kit is sold individually. This OEM kit will include the rubber tube as well as two metal clamps for attaching the line to the machine. The fuel line may be used with snowblowers, lawnmowers, tillers, leaf blowers, log splitters, wood chippers, and other small engines, It will work with machines from many different brands, including MTD, Yard Machines, Troy-Bilt, Yard-Man, Bolens, Cub Cadet, and Husky.

This replacement part is a hand-held oil pump, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This oil pump is small and portable and is able to assist the user during oil changes in their lawn mowers. Oil changes are a normal part of maintenance for many lawn mower models and this oil pump will facilitate that.A user might require a new oil pump if the old one is damaged. This part with the lawn mower at purchase, so it may need to be purchased after the fact. It makes changing the oil inside of the engine very easy.This hand-held oil pump is sold individually and is a genuine OEM replacement part sourced directly from the manufacturer. This device can come in handy for those looking to change the oil in their lawn mowers.

This self-tapping screw is used to attach various parts to the engine housing of medium sized gasoline powered engines, in particular yard tools such as tillers, snow blowers, yard tractors, riding mowers, power vacuums, shredders, and chippers. It is used in over 150 different gasoline powered engines. Screws such as these are used particularly when a device is going to receive a great amount of vibration and stress while the engine is running and rotating tools are engaged. Such devices sustain a great deal of wear over time and the parts subject to replacement will eventually fail and need to be replaced. In such cases, it is wisest to replace the attaching hardware such as housing screws as well, because it is a self-tapping screw. Screws of this type are designed to forge a tight bond between the metal pieces they are securing together, but once loosened, they should ideally be replaced with new hardware. Make sure when replacing these screws to use genuine OEM parts like these screws. These replacement parts are manufactured to be identical to the original pieces. This hex screw is compatible with the following brands: MasterCut, Yard-Man, Yard Machine, Montgomery Wards, MTC, Murray, Bolens, Craftsman, Turf King, Troy Bilt, Cub Cadet, Huskee, Toro, and Ryobi.

This part is a replacement clutch collar. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. It is intended to replace a defective clutch collar in tillers.The clutch collar is an essential component that ensures the equipment's clutch is able to function properly. If the clutch collar is broken or faulty in any way, the user may struggle to change gears and properly control the tiller. Thus, this part will require replacement. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this clutch collar, the appropriate owner's manual and equipment diagrams should be referred to. This clutch collar is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with tiller models that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands.

This replacement part is a gear spur, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. Gear spurs are found inside many different types of machinery and are important to the overall workings of the device. Gear spurs are different from other gears as they have ridges along the edges allowing the gears to turn in one direction rather than the other. A new gear spur might be needed if the user hears unusual noises coming from inside of the engine. It is possible that the ridges on the outside of the gear can become stripped overtime and it might be best to replace this part. Be sure the engine is completely powered off before starting this repair as it can become dangerous if the gears are activated. This part is a genuine OEM replacement part. This gear is sold by itself and sourced directly from the manufacturer.

This o-ring is a genuine OEM part sourced from the manufacturer for use in many parts of engines in lawn and garden equipment. The o-ring is a type of gasket but is not flat like a gasket. It is circular and made of rubber. It is seated in a groove on the engine part and is compressed against another part to create a seal. This seal keeps air and fluids from entering or exiting the sealed part. Like gaskets, o-rings must be periodically inspected and replaced to ensure proper engine performance.Visual inspection of o-rings will reveal nicks, indentions, cuts, or tears on the surface of the o-ring. If the rubber has warped due to excessive heat, it will not fit properly and will need to be replaced. The replacement may not require tools, depending on the location of the rubber gasket. Remove the bad o-ring and wipe both sides of the area to remove the old grease. Apply fresh grease to the o-ring before installing it to ensure a tight seal. Press the new o-ring firmly in the groove before attaching the connecting part. If the ring does not seat well or has to be stretched to fit, discard and start with a new o-ring.The o-ring is sold individually. It is designed for trimmers and tillers. It is compatible with Craftsman, MTD, Bolens, Troy-Bilt, and Cub Cadet.

This replacement part is a screw knob. This is a genuine replacement part made by MTD. This screw knob is used in different types of machinery and appliances. This screw is easily gripped to remove and replace easily and quickly. A new screw knob might be needed if it is so worn that the user can no longer grip the screw. This can be due to wear and tear after years of normal use. If the screw part has become stripped it is recommended that it be replaced as soon as possible. This should be a fairly easy replacement and only require common household tools. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use. This screw knob is also sold individually and is sourced directly from the manufacturer.

This part is a replacement ignition coil. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective ignition coil in cultivators.Ignition coils are important for powering the cultivator as they generate the voltage that travels to the equipment's spark plugs. If the ignition coil is faulty, the cultivator may have decreased power or may not work at all, thus this part may need to be replaced. Disconnect the spark plug wire before installing the ignition coil. It's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this ignition coil, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This ignition coil can be used with different models of cultivators that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Sold individually.

This is a genuine replacement fuel tank for a tiller. The fuel tank holds fuel for the tiller and connects fuel tubes to distribute fuel to the engine. Tiller fuel tanks may start to leak if it is cracked, punctured, or otherwise damaged. In addition to losing fuel, this is a serious safety hazard. If damaged, this part should be replaced before using the tiller. Do not attempt to repair a damaged fuel tank.Fuel tank replacement is a simple process. This project will require different tools depending on the model of tiller. Remove the fuel lines and fuel tank completely from the tiller. Remove the tiller fuel tank by unscrewing any bolts connecting the fuel tank to the engine. Set up the new fuel tank with the filter, fuel level indicator, and fuel cap. Reinstall the fuel lines from the engine to the fuel tank, and reattach the new fuel tank with the previous or new bolts.This is a genuine OEM replacement part. This part is compatible with Craftsman, Troy-Bilt, and MTD brands. This part is sold separately.