Dryer Igniter Bracket Parts

This hinge retainer plate secures the appliance door hinge to the cabinet or door, keeping alignment and smooth operation. Replace a bent, stripped, or missing plate to stop hinge wobble and help the door close and seal properly.

• Anchors the door hinge and distributes load to prevent shifting
• Maintains proper door alignment and gap for smooth opening/closing
• Helps prevent door sagging, rubbing, or poor gasket sealing
• Typical symptoms include a loose hinge, wobbly door, or door not closing flush

• Disconnect power and support the door before removing any hinge fasteners
• Mark hinge locations to preserve alignment during reassembly
• Install the plate in the correct orientation; transfer any spacers/shims in original order
• Tighten fasteners evenly, then verify door alignment and gasket seal

This replacement igniter lights the gas burner in your range or wall oven, restoring reliable starts and consistent heat. Swap in a fresh igniter to resolve hard-to-light burners and no-heat situations so cooking cycles begin as they should. What it does:

• Provides the ignition source to light the bake or broil burner flame
• Helps ensure fast, consistent burner light-off at the start of a heat cycle
• Common symptoms of failure: no ignition/no heat, delayed or intermittent ignition, repeated clicking without flame, or a gas odor before light-off

• 1 igniter assembly

• Disconnect power and shut off the gas supply before servicing; allow the appliance to cool completely
• Note wire connections and mounting orientation from the original part for correct reassembly
• Handle the ceramic/element carefully to avoid damage
• After installation, restore gas and power, then check for leaks with a soap solution

If the mounting clip is burnt order WE1X941.

This rear panel support is the structural bracket that secures the appliance's rear cover/backguard in place. Replacing a worn or broken support restores proper alignment, helps protect internal components, and reduces vibration noise.

• Secures the rear panel/backguard to the chassis for stable, proper fit
• Maintains alignment of panels and mounting points
• Helps minimize vibration, flexing, and rattles from a loose rear panel
• Common signs of failure: cracked or missing bracket, stripped mounting points, panel movement or buzzing

• Disconnect power at the breaker; shut off gas supply
• Pull the appliance forward carefully to access the back; protect flooring
• Remove fasteners, replace the damaged support, and reuse original hardware/clips
• Keep wiring clear of sharp edges; tighten screws evenly without over-torquing and check for vibration before repositioning

This gas dryer igniter assembly heats to a bright glow to light the burner so the dryer can produce heat. Replacing a cracked, weak, or non-glowing igniter restores reliable ignition and proper drying performance.

• Heats and ignites the gas at the burner to start the flame
• Restores drying heat when the original igniter is cracked or electrically open
• Common symptoms include: dryer runs but no heat, burner never lights, igniter does not glow, or extended dry times
• Visual damage such as white spots, breaks, or crumbling on the element indicates failure

• Disconnect power and shut off gas supply before servicing
• The igniter is brittle—handle only by the base or bracket; avoid touching the element with bare fingers
• Mount in the same position as the original and route leads away from heat and moving parts
• After reassembly, run a heat cycle to check the burner ignites; also check the flame sensor and gas valve coils

STACK KIT FOR LONG VENT DRYER

This glow-bar igniter lights the gas burner in your dryer so it can produce heat. When the igniter is cracked, weak, or open, the burner won't light and clothes won't dry properly.

• Heats up to ignite the gas burner during each heating cycle
• Common symptoms of failure: no heat, takes too long to dry, burner won't light, igniter doesn't glow or glows but no flame
• Restores consistent ignition and drying performance

• Unplug dryer and shut off gas supply before servicing
• Handle the igniter carefully—ceramic element is fragile; avoid touching it with bare fingers
• Note wire routing and burner alignment before removal
• After installation, restore gas/electric and check for proper burner ignition

Includes 2 adhesive pads, 2 brackets, 4 screws, and installation instructions.

The Dryer Spring Plate is essential for maintaining the smooth operation of your Samsung dryer. This genuine OEM part is specifically designed to provide reliable support and stability, ensuring your dryer functions efficiently. Crafted from high-quality materials, the spring plate helps absorb vibrations and reduce noise during the drying process, enhancing the overall performance of your appliance. Installing the Dryer Spring Plate restores the proper alignment of your dryer's components, which can lead to longer appliance lifespan and fewer repair needs. Compatible with a wide range of Samsung dryer models, this spring plate guarantees a perfect fit and easy installation. By choosing this genuine OEM part, you can trust in the authenticity and durability that matches the original design of your dryer. Whether youGÇÖre replacing a worn-out spring plate or upgrading your dryerGÇÖs performance, the Dryer Spring Plate offers a dependable solution to keep your Samsung dryer running smoothly. Enhance your dryerGÇÖs functionality and enjoy the peace of mind that comes with using high-quality, manufacturer-approved components.

This ground strap assembly bonds the dryer's cabinet to the designated ground point, helping ensure safe operation. Replace a damaged or missing strap to restore a proper ground path and reduce the risk of shocks or nuisance static.

• Maintains the required electrical bond between the dryer chassis and ground as designed
• Helps prevent electric shock and reduces static by providing a low-resistance path to ground
• Replace if the original strap is loose, corroded, heat-discolored, broken, or missing
• Symptoms can include a slight tingle when touching the appliance or visible damage near the ground/terminal connection

• Disconnect power at the breaker before servicing; verify no power with a meter
• Follow your model's wiring diagram; bonding differs for 3-wire vs 4-wire cord installations per local codes
• Clean contact surfaces and secure fasteners firmly for a solid metal-to-metal bond; replace any heat-damaged hardware
• After installation, verify continuity between the cabinet and the designated ground point

The Igniter is an OEM part for GE dryers. This part is responsible for generating a spark or glow that ignites the gas, producing the necessary heat to dry your clothes effectively. It ensures that the dryer reaches and maintains the desired temperature throughout the drying cycle.

A bad igniter can occur due to wear and tear, electrical malfunctions, or damage from excessive heat. If you notice symptoms such as the dryer not heating up, a lack of heat during the drying cycle, or the burner not igniting, it may be time to replace this part.

Symptoms of a bad igniter include:

• Dryer not heating up
• Lack of heat during the drying cycle
• Burner not igniting

Restore your GE dryer by replacing the faulty igniter with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This accessory assembly is the factory-specified kit used to attach or secure designated parts on your appliance. Replacing missing or worn pieces restores a solid, factory fit and finish.

• Provides the original mounting/attachment components specified for your model
• Replaces lost or damaged hardware after installation, moving, or service
• Helps correct loose, misaligned, or rattling parts caused by missing fasteners
• Maintains proper alignment and appearance of exterior parts such as trim or handles

• Disconnect power; also shut off water and/or gas supplies before servicing
• Protect finished surfaces; start fasteners by hand to avoid cross-threading or damage
• Follow your model's service or installation guide for correct order and placement
• After assembly, verify everything is secure and test operation before returning to service

This Supporter, Leg is the base bracket that holds the leveling foot at the cabinet. It stabilizes the unit and enables precise leveling to help prevent rocking, vibration, and door or drawer misalignment during everyday use.

• Supports and locates the leveling leg/foot at the base of the cabinet
• Provides a secure mounting point for height adjustment and stability
• Helps keep the cabinet square and reduces wobble and vibration
• Common symptoms of a failed support include rocking, difficulty leveling, or a visibly cracked/bent bracket

• Disconnect power and protect flooring before moving or tilting the appliance
• Access the base area (remove the toe grille/kick panel if equipped)
• Unload the leg, remove mounting fasteners, and transfer the leveling foot to the new support if needed
• Reassemble and verify the unit is level front-to-back and side-to-side

This small structural bracket supports the "leg" of an interior shelf or drawer assembly in compatible refrigerators. It helps keep shelves level and stable so bins slide smoothly and contents stay secure during everyday use. What it does:

• Supports the corner/leg of an interior shelf, cover, or drawer rail
• Helps maintain level alignment and prevents wobble or sagging
• Restores stability if the original piece is cracked, warped, or missing
• Common symptoms: shelf or drawer sags, binds, or rattles; poor fit/alignment

• 1 supporter leg

• Disconnect power and remove food from the affected area before starting
• Remove the shelf/drawer and note fastener locations or locking tabs
• Transfer any reusable screws/clips and seat the new supporter fully
• Reinstall components, ensuring the shelf/drawer sits level and moves freely

A stacking kit that lets you securely mount a compatible dryer on top of a front-load washer to save floor space and improve stability. Designed for factory-specified stacking applications when used with approved appliance pairs. What it does:

• Provides the hardware and brackets needed to secure a dryer to a front-load washer and reduce shifting during use.
• Helps keep stacked appliances aligned for safer operation and less vibration-related movement.
• Intended for factory-approved stacking configurations—ensures the dryer stays fixed to the washer when installed per instructions.
• Can help maximize laundry room space by enabling safe vertical installation where compatible.

• Follow the appliance manufacturer's stacking instructions exactly; use the OEM procedure and supplied template if provided.
• Disconnect power and gas and empty both appliances before starting; wear appropriate safety gear.
• Installation may require two people and basic hand tools; the stacked unit is level and stable after installation.

This gas dryer igniter is the glow-bar element that lights the burner so your dryer can produce heat. Replacing a worn, cracked, or non-glowing igniter restores reliable ignition and consistent drying performance.

• Heats and glows to ignite gas at the burner assembly
• Common symptoms: dryer runs but no heat, igniter does not glow, burner won't light
• Visual cracks or a non-heating element indicate failure

• Disconnect power and shut off the gas supply; allow the burner area to cool before service
• Handle by the base only; the igniter element is extremely fragile—do not touch or bump it
• Transfer bracket and wiring from the old part if needed; reuse existing hardware
• Restore gas and power, then the igniter glows and the burner lights properly