Refrigerator Slow Clamp Line Mover Regular Spring Parts

• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

Much easier than expected, I was certain it had to be a water line but the solved everything Read more

• Door latch failure
• Ice maker not making ice
• Not dispensing water
• Ice maker won't dispense ice

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

Ordered a new seal, and replaced it with a new one freezer works great now. Read more

• Fridge too warm

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

The ice chute flap wasnt closing. 1. I turned off power 2, Pulled off facia around controls on freezer door,, you have to pull out the bottom part of the chute first , its clipped in 3. Disconnected the front panel 4. Unscrewed the next panel to allow access to the chute flap 5. Removed 1 screw holding complete flap and mechanism and replaced with new 6. Re installed all parts in reverse Problem was the chute flap had worn and was folding over on top edge when opened and then wouldnt return... Read more

I order both the paddle and spring and watched a video on how to remove the operating panel to replace them Read more

I replaced the lever asm. and spring Read more

1) Remove toe kick panel - 2 Philips head screws 2) Lay down on floor. This might be the hardest part of the repair from some people! 3) Remove broken spring, no tool required. 4) Using your fingers, slip one end of new spring into hole on lever arm. (If you're not sure how it should go, look at the spring on the other door, assuming you have a side-by-side.) 5) Hook the other end of the spring around a round-shank screwdriver. (Don't even bother with pliers. You will disregard this advice... Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

Replaced tubing and fitting Read more

My husband told me about your site and he was right (one more time, lol), I looked for it, so this c/s rep ELIZABETH was so nice and patience helping me until we finally got to the right part. Then instead of 1 piece, I decided to order 10, lol. I will and I did recommend you guys better than other sites. With the price of ONE in other places, I got TEN with you, that's why I got so many. Tks very much! Read more

The old filter head was broken at the supply line side connector fell out. The clicking noise eventually caused the fridge to warm up and stop cooling. The clicking was the overload relay tripping. The Start solenoid on the compressor was an Embarco TSD part 513604044. APP does not have that part nor does any else found a similar one on ebay but I ordered the PTC assembly 6749C-0014E. I removed the overload relay and capacitor from the TSD used two pieces of wire and connectors to create the... Read more

Walk into the kitchen on 21 Sep. Eight year old Frigidaire refrigerator appears to be short cycling, controls are nonfunctional. Unplug it for a few minutes, plug it back in, appears to return to normal function. Return to kitchen half hour 45 minutes later it's short cycling again. Panel has codes on it (S or 5 E CE, later that changes to S or 5 Y CE). Research of codes says replace main board and control board. Not sure where this main board is. 22 Sep call appliance repair. "Soonest... Read more

When I took it apart I found that the drive cup was cracked, the helix lock plate hole was reamed out and the ice deflector spring was broken. The biggest problem was the helix had slipped down the shaft and allowed the end of the shaft to bore a hole in the housing which made it a bear to get out. Others have had the same problem. Once I got past that obstacle, it was simple to replace all the parts and it's working like normal again. Very helpful video explaining the repair. Read more

Downloaded the Technical Service Guide and followed the instructions for removal of the Door Closure Mechanism. Items the instructions failed to mention: 1. Although they took the trouble to call for removal of a 3/16" Allen head bolt, they referred to the closure mounting bolts as just "bolts". In fact, they were T-25 bolts. If I didn't have a Torx kit, it would have required a trip to the Orange Big Box Home Center to complete the job. 2. Although the instructions don't describe this step,... Read more

I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well. Read more