Refrigerator Tape Incorrect Mount Detergent Parts

This door gasket presses into slot around door pull off old and press in new a five minute repair Read more

Very easy to do. Read more

I bought new gaskets, which were expensive! At least the repair was easy. Pulled out the old ones, pressed in the new ones. Had to redo them because I didn't notice the little flaps that need to be covering the space in the middle, between the doors. So, pulled them off, and turned them around, and pressed them on again. Maybe 10 minutes? Read more

Walk into the kitchen on 21 Sep. Eight year old Frigidaire refrigerator appears to be short cycling, controls are nonfunctional. Unplug it for a few minutes, plug it back in, appears to return to normal function. Return to kitchen half hour 45 minutes later it's short cycling again. Panel has codes on it (S or 5 E CE, later that changes to S or 5 Y CE). Research of codes says replace main board and control board. Not sure where this main board is. 22 Sep call appliance repair. "Soonest... Read more

Replaced the seals Read more

Thanks to the Appliance Pro video and next day delivery, the fix was easy. Removed the old seals by hand and placed the new seals around the door shelves and eased it into the grove in the door. Read more

Removed freezer door by removing 4 bolts holding slide tracks for freezer basket. Pulled out old gasket. Soaked new gasket in hot water to smooth out a crease that resulted from shipping. Installed new gasket, starting at corners. Used a blunt tool to push new gasket into slot at the corners. Set remaining gasket material with hands. Used putty knife to tuck edge of gasket under lip along door. Reinstalled door. Take care to line up door perpendicularly. There is some play when... Read more

It could not have been easier. I simply pulled the old gasket off and pushed the replacement gasket in place until it was secure all around the door. Very easy fix. Read more

Right-side gasket replacement was straightforward. Left side required removal of mullion, which stumped me. I contacted Appliance Parts Pros who gave me the necessary instructions: Remove the center screw and lift up the mullion. Simple enough, once I knew how to do it. Read more

• Door sweating

With no problem at all Read more

Door gasket was easy to remove and reinstall. Original gasket was penetrated while cleaning food stuff from folds in the seal below the frig doors. (Gasket is very fragile so don't try to expand the folds while cleaning. I used my finger and a paper towel but in hindsight should have used a Q-Tip. Also, when installing the new gasket you have to be sure the seam folds over the edge of the door and doesn't get caught underneath. Read more

Ordered a new seal, and replaced it with a new one freezer works great now. Read more

Emptied the freezer and removed the drawers to allow access to the seal. Read more

The tray was simple, pick up the old one, pop in the new one. The gasket for my refrigerator was almost as easy. When I received the part I opened it up and let it lay flat for about 3 days (probably overkill). The old gasket popped right out and the new one went in really easy. The entire job took me about 10 minutes to do, no tools required. I do recommend that you start with corners and work your way to the middle of each side. I found that would prevent any stretching. You also need to... Read more

The rubber seal/gasket was torn on our KitchenAid refrigerator right side door. I purchased the replacement and followed the directions/recommendations of how to prepare the new gasket for installation. When it's removed from the shipping box, it does have wrinkles and preparing it is a must. I set it out on our tile floor and then used a heat gun (low setting) to warm it up and massage it. It took me about 15 minutes, stopping and restarting as I let the rubber come back to it's desired shape.... Read more

Ordered a new freezer door gasket. Once I entered the model number into your system, the part was identified and then it was easy to order. Read more