Washer Condensate Overflow Float Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10285512
Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.
Do-It-Yourself Stories from Customers like You
Temperature control switch failed to cold only. Marilyn M. • Summerfield , FL • September 30, 2017
Replaced with a new one.
Read more
More
$83.44
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: 279872
This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.
- Provides precise resistance to reduce voltage/current in the designated dryer circuit
- Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
- Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
- Replace if visibly burned/damaged or if testing shows an open or shorted condition
What's included: One resistor Install notes:
- Disconnect power to the appliance before servicing
- Access the console/wiring harness and note original wire routing
- Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
- After installation, run a test cycle to ensure proper operation of the affected function
Do-It-Yourself Stories from Customers like You
The dryer timer would advance to the cool down cycle but would not shut off a the end of the cycle. John C. • Sunbury , PA • July 14, 2017
I thought the problem was the dryer timer, so I ordered a timer to make the repair. When the part arrived I wasn't sure how to install it because the wiring was slightly different from my timer. Before installing the timer, I had a friend run a meter test on the timer to verify this was the problem. After checking the timer it checked out as being ok, so with further research I found out that if the timer power resistror part is bad it would cause the dryer to not shut off at the end of the...
Read more
More
$46.35
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: W11417623
Fix a washer that won't fill with water or overfills with this water level pressure switch. Controls proper water amounts for each wash cycle.
Do-It-Yourself Stories from Customers like You
Water wouldn't fill the basket Mike R. • Essington , PA • December 03, 2016
Replaced the faulty switch with the new part. Found out tge problem by doing a simple Google search!
Read more
More
$52.68
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10192994
This replacement switch restores reliable on/off control for the specific function it serves in your appliance. A failing switch can cause that feature to stop responding or behave intermittently; replacing it brings normal operation back.
- Opens and closes the electrical circuit to the associated component when actuated
- Provides consistent, safe control of the feature it operates
- Typical failure symptoms: function won't turn on, won't turn off, or works only intermittently
- Physical clues can include a loose or sticky actuator, heat discoloration, or visible arcing damage
What's included: 1 switch Install notes:
- Disconnect power at the breaker before servicing; allow hot surfaces to cool
- Access the switch per your model's service/parts diagram and note wire positions
- Transfer wires one at a time to the new switch; secure any mounting hardware
- Verify continuity and test operation before reassembly; replace any damaged connectors
Do-It-Yourself Stories from Customers like You
Washer would not start running thought door was open C. D. • Austin , TX • April 28, 2017
This switch fixed a very frustrating problem, 75% of the time the washer refused to run because it "thought" the door was open. Replacing the switch was a very easy, in expensive, 5-min fix. The washer runs like new.
When taking off the gasket, there is a metal ring that holds the gasket in place. It is connected by a spring. Find the spring, put a flat head screwdriver between the spring and the gasket and pull the ring off. The gasket will then peel back, giving you access to the switch and...
Read more
More
$36.95
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10268911
Washer overfilling or underfilling? The water level pressure switch senses tub pressure to control fill cycles. DIY repair in 20 minutes or less.
Do-It-Yourself Stories from Customers like You
My washer was overfilling Steve T. • Warwick , NY • January 25, 2016
Called appliance parts and asked, what was the fix. Told it was fill switch and that I could order it.
I was amazed that I received the part the next day without even asking for overnight delivery. I installed the part in less then 20 min. Problem fixed..
Read more
More
$111.44
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22004243
Washer won't start or spin? A faulty lid switch prevents operation when the lid position isn't detected. Simple clip-in replacement, typically done in 10 minutes.
Do-It-Yourself Stories from Customers like You
The washer quit working Andrew S. • Franklinville , NY • March 27, 2014
Took off the back of the top pushed the switch forward and lifted it out after I unplugged it. Put the new switch in the opposite of how I took it out, plugged in the wires put the back on and finished my laundry.
Read more
More
$75.95
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Frigidaire part
By: Frigidaire
Part Number: 134813660
This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.
- Monitors door position and allows the cycle to run only when closed
- Interrupts power to stop operation when the door opens
- Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display
What's included: 1 door switch Install notes:
- Disconnect power to the appliance before servicing
- Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
- Move wires to the new switch one at a time to maintain correct positions
- After reassembly, test switch operation before running a cycle
Do-It-Yourself Stories from Customers like You
Open door Carlos R. • Yonkers , NY • January 16, 2018
Replacing door switch.
Read more
More
$18.29
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: W10121657
Fixes F02 drain error codes and slow draining. This small ball creates a seal in the tub-to-pump hose to control water flow. Simple DIY replacement.
Do-It-Yourself Stories from Customers like You
F02 fail to drain repeated suds warnings John C. • Eagle River , AK • February 18, 2019
Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ...
Read more
More
$14.43
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3356467
Washer won't fill properly or overfills? This water level pressure switch senses fill levels and signals when to stop. Easy DIY fix for cycle timing issues.
Do-It-Yourself Stories from Customers like You
Wash machine once in a while would stop running Daniel B. • Leesburg , FL • May 13, 2016
I found that turning the water level switch back and forth would activate the machine So I replaced the water level switch and the plastic hose that connected to it.
I purchased a clamp in the purchase, but it was the wrong size! There wasn't a clamp used in the original set up, so I installed the switch and hose without it! It was the video instructions and having the correct parts that made that made this a easy repair!
Thank You
Read more
More
$108.40
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Frigidaire part
By: Frigidaire
Part Number: 134762000
Fix E32 error codes or washer stopping during fill with this water level pressure switch. Senses water level and controls fill cycles. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Washer would stop after about 30 second on fill cycle diagnostic code of e32 Kenneth B. • Friendswood , TX • June 04, 2016
The E32 diagnostic code that the Frigidaire washer was throwing after a quick water fill attempt was not in the supplied Data Sheet that came with the washer and Frigidaire would not provide and updated Data Sheet because, "it's a liabiliity issue" was their statement, but they did tell me that the problem was in the Fill Pressure Sensor/Wire Harness or the Main Control Board (the display board). I ordered the Pressure Sensor and Main Control Board from AppliancePartsPros after checking...
Read more
More
$91.31
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Speed Queen part
By: Speed Queen
Part Number: 55882
This is a start switch intended for use with dryers. With time or because of damage caused by accident, the start switch may stop working correctly. If the start switch isn't working, then the dryer will not function properly, and a replacement part should be ordered. If the push to start switch doesn't respond, it could be damaged or broken. Replacing the push to start switch on a dryer is a simple process. Start by unplugging the machine. Remove the back panel and pull out the old push to start button. Put the new button in its place and reattach the rear panel. Wear gloves for protection. Restore power only after the complete reassembly is performed. This push-to-start button is a genuine OEM replacement part. It is sold as an individual unit. The part is sourced from the manufacturer and made of durable materials. The push-to-start button can be installed in various dryer models made by SpeedQueen and Alliance brands.
Do-It-Yourself Stories from Customers like You
Would not start. The start button had fallen into the dryer. Chris B. • Brillion , WI • January 02, 2023
Replacing it couldn't be easier. Two screws to remove the control panel and swap out the Start Switch.
Read more
More
$51.59
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21001554
Fix washer overflowing or not stopping fill cycle. This water level pressure switch senses tub water and signals control to stop filling. DIY repair.
Do-It-Yourself Stories from Customers like You
Tub was overfilling and water would not stop until machine turned off replaved water level valve but did not solve problem Kirk N. • Oak Island , NC • April 19, 2014
Filled tub to about 6 inches and inspected washer. Noticed that the tube leading from the air entrapment bubble on the exterior side of the drum had a small leak in it. Clipped off the part of the tube that had the hole in it(it was very close to the connector nipple) reconnected and problem was solved.
Read more
More
$118.53
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694419
This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:
- Produces audible tones for cycle end, timers and other appliance notifications
- Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
- Helps you hear and identify completed cycles and timed alerts
- Small, mountable unit that fits behind the control panel and connects to the control board
What's included:
- One adjustable buzzer kit
Install notes:
- Disconnect power before servicing to avoid shock risk
- Access may require removing the control panel; keep fasteners organized for reassembly
- Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
- Test buzzer function with power restored before fully reassembling
Do-It-Yourself Stories from Customers like You
My electric dryer wasn't heating during drying Deborah H. • Athens , MI • January 20, 2020
I was looking for a parts sight and found yours. I started to watch all the video tutorials on each part and the "check these connections first video". Well by doing this I was able to find the source of my problem. What I thought was the heating coil not working right, ended up being the timer that was bad!!! I am so very happy with your sight and the step by step videos that were the success to being able to do this on my own.
Read more
More
$71.95
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Speed Queen part
By: Speed Queen
Part Number: 203935
Fix a washer that won't start or respond to controls with this switch assembly. Restores electrical switching in control and safety circuits.
More
$10.95
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3362987
Washer won't fill or overfills? Water level pressure switch senses tub water and controls fill cycles. Restores accurate fill levels and agitation.
Do-It-Yourself Stories from Customers like You
No agitation Paul S. • East Calais , VT • August 08, 2016
Initially suspected timer, but it did advance during some cycles. the schematic on the unit and other input on this site helped to confirm that the water level switch was at fault
Read more
More
$113.46
IN STOCK
Most orders arrive by Wednesday, November 25
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10085220
Washer won't start or shows electrical faults? A failed ground switch disrupts the safety circuit. This switch restores proper grounding for reliable operation.
Do-It-Yourself Stories from Customers like You
The code was f20 which means not enough water flow. Bruno R. • Franklin Square , NY • April 10, 2021
Watched YouTube and ordered parts then replaced the parts and walla !!!! All was good.
Read more
More
$21.34
IN STOCK
Most orders arrive by Wednesday, November 25