Washer Bake Element Terminal Wiring Parts

Dryer won't auto dry or cycles run too long? This moisture sensor wire harness connects sensor bars to control. Restores accurate dry cycles. DIY-friendly.

Includes screws and wire connectors. For the complete terminal block kit use 279320.

The Motor Wiring Harness is an OEM replacement part for LG washing machines. It is responsible for supplying power from the washer control board to the motor and related components. The wiring harness conducts electrical current, allowing for the operation of the pump, motor, and other vital systems. 

Causes of a bad motor wiring harness can include damage due to repetitive use and wear over long periods of time, exposure to moisture, impact or abrasion damage, or faulty insulation leading to electrical shorts.

Symptoms of a bad motor wiring harness include: 

• The washer failing to start or functioning intermittently
• Strange noises coming from the motor or other electrical components
• Slow or ineffective spinning or agitation  
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore washing machines. 

Washer won't spin or shows LE error? A faulty motor wire harness disrupts power to the drum motor. DIY fix in 20-60 minutes with basic hand tools.

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

Electric heating element assembly that generates heat during drying cycles. Replace when the original element burns out, breaks, or fails to heat properly.

Replacement heater assembly for washers. Installs in the wash tub housing. Replace if cracked, leaking, or damaged. Includes integrated thermistor sensor.

10-inch heating element that restores proper heat production in affected appliances. Replaces a worn or failed element to help resolve issues like no heat or unusually long cycle times. What it does:

• Generates heat so your appliance can reach normal operating temperatures.
• Common symptoms it addresses: little or no heat, longer-than-normal cycles, or intermittent heating.
• Replaces a single failed element to return consistent heating performance.

What's included: One heating element. Install notes:

• Disconnect the appliance from power before attempting any repair.
• Allow the element to cool and handle carefully to avoid bending or damaging the coil.
• Ensure the terminal connections are secure and free of corrosion; tighten or replace fasteners as needed.

NOTE: IF THERMISTOR HAS TERMINALS WIRE HARNESS HAS TO BE CHANGED PART# 137288900 PER FRIGIDAIRE

The Wire Harness is an OEM part for Whirlpool washing machines. The wire harness is responsible for transmitting electrical signals that power components and allow them to communicate during each cycle.

Causes of a bad wire harness can be normal wear and tear over time, pinched or cut wires, or wire insulation breakdown due to heat or moisture exposure.

Symptoms of a bad wire harness include:

• Lights or display not working properly
• Washer not starting cycles
• Sensors or switches malfunctioning
• Intermittent operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Washer water heater element raises water temperature during wash cycles. Replace if cracked, corroded, or no longer heating properly in your machine.

Fix washer won't drain issues with this lower wiring harness. Restores electrical connections between drain pump and control components.

Heater assembly for washer dryer combos. Installs in the drying system to generate heat. Replace if cracked, corroded, or damaged to restore proper drying.

Washer won't start or runs intermittently? A faulty wiring harness disrupts power flow between components. This repair restores connections in 20-30 minutes.

Electric heating element that warms water in your washer. Replace this component when cracked, burned out, or fails to heat, restoring proper wash temperature.

Replaces the tub heating element in your washer. Installs inside the wash tub to heat water. Needed when the original element is cracked or burned out.