Washer Band Fin Parts

If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day. NOTE! The retaining rings are... Read more

I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more

The repair was fairly straight foward as shown in the video. However, driving the shaft from the bearings took some doing. It required replacing the use of the board with a spare bolt and a 2lb hand sledge. (having an air hammer as reserve, also not a bad idea) I rated this reair as a "1" however I've been an auto mechanic for 40 years. If you do not have good general mechanical ablities you may find this more challenging as you get it further apart. I suggest anyone making this repair should... Read more

• Spins slowly
• Will not agitate
• Pumps but will not spin

My parents have the older 80 series washer and dryer that gets used way more than a consumer washer and dryer was ever meant to be used. The washing machine finally said im tired. During the spin cycle it was making a really loud squealing noise and during the agitation cycle it would barely agitate the clothes. So i ordered the basket drive to get rid of the squealing during spin cycle and noticed the dogs on the cams were warn and werent grabbing so ordered the whole cam kit to be safe... Read more

The fix was so easy 2 screws and done, the part i ordered came the following day, i didnt expect it to arrive for another 3 to 4 days, excellent service , shipping, recieved the correct parts, and they have everything in stock, i would recommend Appliance Parts Pros to everyone, you wont be let down, believe me, thank you for the fast service, i give them 10 stars, Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

• Marks left on clothes

I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more

• Marks left on clothes

Searching for paddles or baffles led me to Appliance Parts. Discovered I didn't have to buy anything in order to view the video which is a pretty nice feature to see if my skills are up to it. "How in the world do I repair something without external screws?" "Take the top off the machine to see if there are any mounting screws and then just smack the baffles toward the rear of the machine with a mallet to loosen and remove?" Easy, really easy. My wife was missing an underwire to one of her bras... Read more

The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more

I removed the dial knob and plate as instructed by the video, removed the front panel of the washer to access the switch. I found the plastic molded bracket that the timer rests on to be broken and the tab on the timer where it is attached by a screw to be broken. I ordered a replacement switch, dial and knob. When it arrived I replaced the parts as instructed, but I had to use super glue to hold the new switch in place due to the support tab on the washer panel being broken off. After letting... Read more

Rather than call a repairman, I looked on line to get a replacement part. AppliancePartsPros.com had clear diagrams of the washer's major subassemblies from which it was easy to identify the broken baffle. AppliancePartsPros.com offered the part at the lowest price I could find online. That price seemed very high for a simple piece of plastic, but I know no alternative way to fix the problem. i ordered the part. It came in a couple of days when I was not home. My wife told me by phone that the... Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more

• Leaking

I replaced the following parts in the GE WASHER that I have owned for approximately 14 years: Part no.: WH08X10038 - rubber gasket Part no.: WH01X10277 - inside gasket clamp Part no.: WH01x10279 - outside gasket clamp The two gasket clamps were ordered on 1/18/24 and delivered the next afternoon to my front door. I already had the replacement rubber gasket from a long time ago. I will mention that I have NEVER tried replacing a part on a major appliance. Since the washer machine is 14 years... Read more

If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more

This was a simple fix since mine didnt need any screws. Slipped in and locked into place. Read more