11025131410 Parts

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The Cap is an OEM part for Whirlpool washing machines. It provides a secure closure over the agitator post. The cap is designed with precision tolerances to fit snugly over the central agitator shaft.

Causes of a bad cap are typically wear and tear through repeated use and continuous exposure to detergents and other wash chemicals. Physical damage from dropping heavy loads could also potentially compromise the cap.

Symptoms of a bad cap include:

• Shifting or loose movement during the wash cycle
• Clicking or clanking sounds from a loose fit
• Improper stabilization of the wash basket

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control board manages the appliance's key functions by interpreting inputs and switching power to components. Replacing a failed board can help resolve unresponsive controls, error codes, or a unit that won't start or operate normally.

• Interprets signals from sensors and the user interface to execute commands and timing
• Switches power to motors, valves, heaters, or fans as required by selected settings
• Typical failure symptoms: dead or unresponsive controls, won't start, random error codes or beeping, stops mid-operation
• Prevents specific functions from activating when selected (e.g., pump, fan, element, or compressor)

• Disconnect power at the breaker and verify no voltage before servicing
• Use ESD protection; handle the board by its edges to avoid static damage
• Photograph wiring and move connectors one at a time to the new board
• Access often requires removing a panel or control cover; follow your model's service sheet for steps and any post-install setup or diagnostics

Includes connector and both clamps.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

Used from harness to top.

This replacement filter captures airborne grease and cooking particles from the vent system. It helps protect the blower and ducting and keeps airflow efficient so your hood or microwave-hood can clear smoke and odors more effectively. What it does:

• Traps grease and food particles to reduce buildup inside the vent path
• Helps maintain proper airflow and ventilation performance
• Replace when torn, warped, heavily saturated, or won't stay seated
• Common symptoms: lingering odors or smoke, greasy residue near the cooktop, visible damage to the filter

• 1 filter

• Disconnect power and allow the appliance and filters to cool before servicing
• Release the retaining tabs or latch and remove the old filter
• Seat the new filter fully and secure per your user guide
• Do not operate the appliance without all required filters installed

Right hand side. For screws use WPW10119828.

Right hand side

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

Size: .20 Fl. Oz. (6 ml)