Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't start or spin? This lid lock magnet triggers the safety sensor to confirm the lid is closed. Simple DIY fix restores normal operation.
Shifter spring for top-load washer transmission mechanism. Replace if spring is broken, stretched, or missing to restore proper shift engagement.
Secures the drive pulley to the motor shaft in your laundry center washer. Replace if stripped, missing, or loose to restore a solid pulley connection.
Covers the top of the washer tub assembly in combo units. Replace if cracked, broken, or missing. Includes rod and spring assemblies for secure mounting.
This is a stacked unit so it comes apart a little different. you DO NOT have to remove the dryer unit to remove the tub assembly.the top front cabinet brace is held on with 6 screws.remove this along with the suspension rods the tub assembly comes straight out the front of the machine. Do yourself a favor and take the whole assembly out of the machine before you disassemble the inner tub. I removed the drain pump before i took the tub out as a precaution. The worst part about this job was the... Read more
Dryer not heating or taking too long to dry? This heating element and housing assembly restores proper heat generation and airflow for even drying.
Replaces the lid actuator that engages your laundry center's lid switch or lock. Needed when the actuator is worn, broken, or damaged from use.
Installed the new Lid Actuator and the dryers Start Switch. Read more
Drain hose assembly routes wastewater from the washer pump to your standpipe or laundry tub. Replace if cracked, kinked, leaking, or causing floor puddles.
First of you need to remove front panel of the washer, using a putty knife push the tabs between the top of the machine and the front panel. Once front panel is exposed drain hose is connected to pump which is in the front of the machine,very easy to access with the front off. Remove old hose with pliers and discard ,run new hose thru outlet on the back of the machine and secure new hose to drain and secure hose to the machine, reinstall front panel of washer and that's it Read more
Fixes loud spin cycle noise, leaking from bottom, or poor agitation. This transmission assembly drives wash and spin cycles. Moderately difficult repair.
Dryer not heating or shutting off mid-cycle? A faulty safety thermostat can cut heat when temperatures climb too high. Direct heater duct mount part.
Dryer won't start? A blown fuse is often the culprit. This part restores power to the circuit. Easy DIY fix—test with a multimeter first.
First I check the breaker for the dryer then I check the power cord and the ohms to the power cord when all this things were in working order I then check the ohms to the fuse to the control panel. The fuse had no ohms so I got a pair on needle nose pliers pulled out the fuse and replace it worked just find after that Read more
Mounts in the washer's drive mechanism to support the shift fork. Replace if the assembly is cracked, broken, or worn to restore proper gear shifting.
Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.
Won't start, spin light blinking, or won't stop spinning? This control board manages cycles and settings. Common DIY repair, typically installed in minutes.
Remove the 2 screws that hold on the front cover just above the washer, the control board is in front of you. Remove the 2 small screws that secure the board, they are star screws, very small ones, do not drop them, for they will fall into the washer tub. Take a picture of the wiring harness, press the 2 tabs on each side of the board, left and right side, the board will pop out. replace the wiring harness, wiring harness has tabs that hold them in place. Also, check the magnetic lid switch,... Read more
Fix blocked motor error codes and no-spin issues in your washer dryer combo. This drive motor and shield kit restores agitation and spin. 30-minute DIY.
I tried to just replace the speed sensor first which was inexpensive but that did not get it going. So I ordered the motor kit which does not come with a new pulley or speed sensor.Remove the pulley and speed sensor from the old motor and install on the new... Clear the code and its good to go Read more
Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.
It was easy, I got the model number of my dryer, then I went on google and found your website. You got a perfect diagram of the door of my dryer. After I saw the video relate it to my problem, I purchased the parts that I need it to fix it, I didn’t need my husband to do it for me. I gave him a surprise after he got home for work. It was all done. Thanks Read more
Mounts on the transmission shaft to transfer motor power for agitation and spin. Replace if worn, cracked, or causing belt tracking issues.
By replacing it. Read more