665 75843005 Parts

This replacement wire restores a reliable electrical path between appliance components. Use it to replace a damaged or heat-stressed lead so power or signal can flow correctly for consistent, safe operation.

• Carries electrical power or signals between components to restore continuity
• Helps resolve issues caused by broken conductors, loose/burned terminals, or brittle insulation
• Can address intermittent operation or components not energizing due to an open circuit
• Ideal when the original lead shows scorching, melting, or corrosion

• Disconnect power (and shut off gas/water if applicable) before servicing
• Document wire routing and connections before removal to ensure correct reassembly
• Transfer any reusable sleeves, clips, or ties from the old lead if present
• Seat connections fully and route the wire away from sharp edges and high-heat areas

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Bushing, Door spring

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This small retainer secures the flexible tine-row "comb" on the dishwasher rack. Replacing a cracked or missing clip keeps fold-down tines aligned and stable so dishes load properly and rack parts stay in place.

• Holds the flexrow comb firmly to the dishrack to support adjustable/fold-down tines
• Helps prevent the comb strip from loosening or popping off the rack
• Common symptoms: flexrow won't stay attached, tines collapse or misalign, broken or missing clip
• Restores original rack function and stability

• Disconnect power to the dishwasher for safety
• Pull the rack out and locate the flexrow comb and its retainer
• Release the old retainer's locking tabs (a small flat-blade screwdriver can help), then remove it
• Align and snap the new retainer into place; the tines move and lock as intended

Color: light gray. Measures about 3 inches high by 6 inches deep.

This replacement upper spray arm restores strong spray coverage to the upper wash level of your dishwasher. It channels water through its jets and spins under pressure to help deliver consistently clean dishes on the top rack.

• Directs pressurized wash water to the upper wash level for thorough cleaning
• Rotates under water pressure for even spray coverage
• Helps clear food soils and detergent residue from dishes and glasses
• Common symptoms: poor cleaning on the upper rack, spray arm not spinning, clogged or cracked arm

• Disconnect power and shut off the water supply before servicing
• Open the dishwasher; remove the upper rack if needed for access
• Release or unthread the retainer and pull the old arm straight off; clear debris from the hub/feed port
• Seat the new arm and secure the retainer hand-tight; ensure the arm spins freely and run a test cycle

Note: Left Hand side with release lever.

The Rinse Aid Cap seals the dishwasher dispenser's rinse aid reservoir. Replacing a worn, cracked, or missing cap prevents leaks and evaporation, helping the dispenser meter rinse aid properly during the final rinse.

• Provides a tight seal for the rinse aid reservoir
• Helps ensure correct rinse aid dispensing in the final rinse cycle
• Symptoms include: cap cracked or missing; rinse aid leaking or depleting quickly; residue or streaks near the dispenser

• Disconnect power to the dishwasher before servicing.
• Remove the old cap and clean any buildup around the dispenser opening.
• Hand-install the new cap until snug; do not overtighten.
• Fill the reservoir and check for leaks around the cap.

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This access panel covers the lower front of the appliance to shield internal components and provide a clean, finished look. Replace a dented, cracked, or missing panel to restore appearance and help keep debris away from sensitive parts.

• Shields and conceals base components from damage, dirt, and splashes
• Provides service access to the lower compartment when removed
• Helps maintain a tidy, finished front profile
• Common signs it needs replacement: cracked, bent, missing, rattling, or won't stay securely fastened

• Disconnect power at the breaker before servicing
• Remove the existing panel's mounting screws; support the panel as you remove the last screw
• Position the new panel, align mounting holes, and reinstall screws without overtightening
• Verify the panel sits flush and is secure before restoring power