665170 Parts

Seals the pump housing to prevent water leaking from the tub onto the motor. Replace if you see leaks around the circulation pump area. Confirm fit by model.

Third level wash arm assembly for dishwashers. Installs on upper feed tube in top rack area. Replace if disc is cracked, washer is missing, or assembly won't stay on shaft.

Dishwasher leaking from bottom or making grinding noise? The sump housing often cracks or wears out. Moderately difficult repair, about 45 minutes.

This replacement screw fastens appliance components such as panels, brackets, or trim. Use it to replace a missing, stripped, or rusty fastener and restore a secure, rattle-free fit in your appliance assemblies.

• Secures panels, brackets, or hardware to maintain proper alignment
• Helps eliminate vibration, rattling, or loose-feeling parts
• Replaces fasteners that are missing, corroded, or cross-threaded
• Typical signs you need it: loose handle or panel, gaps, or hardware that won't stay tight

• Disconnect power (and shut off gas, if applicable) before servicing
• Match thread type and length to the original fastener for proper fit
• Start threads by hand to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if present

Fix a dishwasher motor that hums or won't start. This run capacitor provides the phase shift needed for smooth motor operation. DIY repair in 30-45 min.

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture

This is a rubber gasket that seals around the door vent opening on a dishwasher, preventing steam and moisture from escaping into areas where they can cause damage. It fits between the vent assembly and the inner door panel. Replace this gasket if you notice moisture or steam leaking from around the vent area, water dripping down the front of the door, or if the gasket appears cracked, warped, or deteriorated.

This door catch and strike work together to keep the door securely closed and engage the safety interlock switch. Replacing worn pieces restores a firm latch and reliable operation when the door is properly shut.

• Aligns and engages the latch so the door stays closed during operation
• Activates the door switch so cycles can start
• Helps prevent the door from popping open mid-cycle
• Common symptoms: door won't latch without force, unit won't start, visible wear or a bent strike

• Disconnect power to the appliance before servicing
• Open the door and remove mounting fasteners to swap the catch and strike
• Adjust strike alignment/depth so the latch engages fully and the door sits flush
• Restore power and test for smooth closing and proper cycle start

Outer door panel for dishwashers. Installs on the front of the dishwasher door. Replace if scratched, dented, or to change color finishes.

Dishwasher won't drain or overflows? A missing or worn check ball can cause backflow issues. This small part maintains one-way water flow in the valve.

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair

Screw for wash impeller.

Fixes water leaking from under the door caused by pressure buildup. This passive vent assembly directs exhaust air out and restores proper venting.

This adjustable manifold is a direct-fit replacement that secures and positions the appliance's manifold assembly so related components line up and function correctly. It restores proper alignment and reliable operation when the original is bent or worn. What it does:

• Provides a mounting surface and adjustable position for the manifold assembly and attached components
• Helps maintain correct alignment so burners/valves operate smoothly
• Restores fit when the original manifold is damaged, bent, or loose
• Resolves symptoms such as uneven burner operation, ignition difficulty, or mechanical misalignment

• Turn off power and shut off gas supply before starting work
• Handle and align carefully to avoid bending; secure with the OEM fasteners
• Check seals and connections after installation; test operation per manufacturer instructions

Replacement outer door panel for your dishwasher. Installs on the front exterior of the door. Order when your panel is cracked, dented, or damaged.

Filters lint and debris from wash water before reaching the drain pump. Replace if cracked or clogged to restore proper draining. Confirm fit by model.