Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Drives the drum rotation for even drying. Replace if dryer drum won't turn, makes squealing noises, or clothes stay wet. Confirm fit with your model.
I found a video on Youtube which described dryer drum squeaks as most likely caused by a worn rear drum bearing. I located the model number on the inside lip of the dryer door: Frigidaire Affinity LEQ6000ES2. I googled "frigidaire affinity dryer squeak". I got a link for my friends at AppliancePartsPros.com! I've used Appliance PartsPros 3 times before, so I figured I was in a "one-stop-solution" situation. I ordered a rear drum bearing kit as well as a dryer drum belt (after nearly 7 years... Read more
Supports and allows smooth drum rotation in your dryer. Replace if you hear squealing, grinding, or rattling noises during operation. Verify fit with your model.
Dryer won't heat or shows E64 error? High-limit thermostat cuts power if overheating occurs. Moderate DIY fix with our video guide and instructions.
My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more
Dryer won't start or shuts off unexpectedly? A failed thermal limiter is often the cause. This safety fuse prevents overheating. DIY repair in 30-45 minutes.
Recommendations have fun and a bucket to prevent losing parts. First watch the videos, practice disassemble and reassemble the dryer drum. Make certain you have a good screw driver and spatula from kitchen (could not find my putty knife). Secondly, clean and inspect everything, make sure the motor bearing and belt pulleys are in good condition with little or no play. Third after you have confidently disassembled, vacuum cleaned, inspected all the worn parts, grease the motor and pulley,... Read more
Dryer drum won't turn or making loud banging noises? A broken drum belt is the likely cause. This belt connects the motor to the drum for rotation.
Replaced the belt. Read more
Washer won't drain or spin? A clogged or failed drain pump is the likely cause. This part removes water from the tub between cycles. DIY repair in 15-30 minutes.
So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more
Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.
The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more
Drive belt connects motor to drum for wash and spin cycles. Replace if washer won't spin, clothes stay wet, or you smell burning rubber. Verify fit.
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more
Dryer won't heat or stops heating after 10-15 minutes? Gas valve coils control burner ignition. Simple 5-10 minute repair with video guide included.
Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more
Dryer not heating or clothes staying damp? This heating element restores proper drying. Moderate DIY repair—requires disassembly and multimeter testing.
Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more
Traps lint and debris during drying to prevent vent clogs and maintain efficiency. Replace when torn, rusted, or bent. Verify fit with your model.
Ordered a new one from the website, matched the model and the picture Read more
Dryer won't start when you turn the knob? A faulty start switch prevents the motor from engaging. Simple 5-10 minute DIY fix with basic tools required.
Got the model number off the dryer. Looked it up online. I wanted name brand replacement part. Found this wonderful AppliancePartsPros.com. Looked up my model number, went to top control panel section, ordered the Start Switch. In ONE DAY I received it. Removed the back part of my dryer. Easily removed the broken part. (I did watch a video online). Put on the new Start Switch. Instead of ordering a new knob. I removed a knob from the dryer that I don't use. It turns a buzzer on or off to let... Read more
Idler pulley assembly for dryers. Mounts on the idler arm to keep the belt aligned and tensioned. Replace if pulley is worn, cracked, or squeaking.
Dryer not heating or flame goes out after igniting? This flame sensor monitors burner temperature to regulate gas flow. Easy 15-minute DIY repair.
Supports the rear of your dryer drum for smooth, even rotation. Replace if drum wobbles, makes noise, or doesn't turn properly. Verify fit by model number.