Lat9593aaw Model--Serial A6129469 Hk Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10135699
The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.
This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.
Do-It-Yourself Stories from Customers like You
Broken spider assembly; aka washer drum shaft assembly Jeff J. • Los Angeles , CA • November 01, 2015
I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point...
We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a...
Read more
More
$13.95
- Compare At:
-
$16.60
- You Save:
-
$2.65
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: 12112425
The Pump and Drive Belt Kit is an OEM replacement part for Whirlpool washing machines. The Pump and drive belt kit is responsible for helping to drain water from the washer drum during the wash cycle. The pump and drive belt kit works by powering the washer's pump to remove water from the drum and out of the washer. The drive belt provides the power to turn the pump, while the pump helps to drain the water. The kit includes 1 pump belt and 1 drive belt.
This part fixes the following symptoms:
- Standing water in the washer drum
- Ineffective or non-existent water drainage
- Potential water damage or flooding caused by a faulty pump or drive belt
Causes of needing to replace the pump and drive belt kit include normal wear and tear over extended use, exposure to debris or foreign objects, or physical damage from impact or mishandling.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.
This part fixes the following symptoms
-
Spins slowly
-
Burning smell
-
Pumps but will not spin
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Maytag clothes washer would not spin or drain Ben M. • Wallingford , CT • September 29, 2018
The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell.
At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer...
Read more
More
$32.43
- Compare At:
-
$44.49
- You Save:
-
$12.06
Genuine Whirlpool part
By: Whirlpool
Part Number: W10820036
The Washer Door Switch is an OEM part for Whirlpool washing machines. This component is crucial for ensuring the washer operates safely by detecting whether the door is open or closed. The door switch prevents the washer from starting or continuing its cycle when the door is open, and it allows the machine to function only when the door is securely closed.
Symptoms of a failing Washer Door Switch include:
- The washer not starting or stopping unexpectedly during a cycle
- Error codes related to door closure issues displayed on the washer's control panel
- The washer door not locking properly or the lock mechanism not engaging
- The washer continuing to operate with the door open
Causes of a bad door switch can include wear and tear from frequent use, damage from repeated opening and closing of the door, electrical faults such as short circuits, or physical damage from mishandling or impact.
This OEM Whirlpool part is also compatible with some models from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore.
This part fixes the following symptoms
-
Will not drain
-
Pumps but will not spin
-
Timer will not advance
-
Doesn't shut off
See more...
Do-It-Yourself Stories from Customers like You
Sometimes the washer wouldn't start the wash cycle when the fill cycle was done it would just sit until the lid was picked up or bumped Eugene N. • Roswell , NM • August 28, 2016
The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new...
Read more
More
$20.95
- Compare At:
-
$32.43
- You Save:
-
$11.48
Genuine Whirlpool part
By: Whirlpool
Part Number: 6-2040130
The Tub Bearing Kit is an OEM part for Whirlpool washers. It includes all the necessary components to replace the tub bearing which is responsible for supporting the inner tub and allowing it to spin smoothly during the wash cycle. Over time, the bearing may wear out or become damaged, leading to excessive noise, vibrations, or even leaks from the washer.
Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads or unbalanced loads that put excessive strain on the bearing, or damage due to water leaks.
Symptoms of a bad tub bearing include:
- Excessive noise or grinding during the wash cycle.
- Vibrations or shaking of the washer.
- Leaks from the washer, around the tub area.
- The inner tub not spinning or becoming stuck.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Note: It is advised to replace the Mounting Stem Repair Kit, part number 6-2040130 at the same time. To complete the repair, you’ll also need a Spanner Wrench to complete the repair (TB123B).
Do-It-Yourself Stories from Customers like You
Leakage from tub seal Gabriel S. • Petaluma , CA • March 15, 2015
I ordered the tub seal and stem seal kits along with the much needed spanner wrench. After viewing the video online several times and taking notes along the way I was ready to tackle the repair. After taking everything apart, I cleaned all areas thoroughly then addressed the rusty areas and mineral deposits found in the tub. Soaking the tub in vinegar and baking soda overnight helped loosen the built up deposits enough so I could carefully scrape them off with a spatula. This was very time...
Read more
More
$56.95
- Compare At:
-
$67.77
- You Save:
-
$10.82
Genuine Whirlpool part
By: Whirlpool
Part Number: 205613
The Water Inlet Valve is an OEM replacement part for Whirlpool washing machines. It is responsible for controlling the flow of water into the washer tub, ensuring the proper water level and supply for each wash cycle.
Causes of a bad water inlet valve can include sediment buildup or obstructions, electrical malfunctions, or normal wear and tear over time, leading to valve failure or improper operation.
Symptoms of a faulty water inlet valve include:
- The washer not filling with water or filling slowly
- Incorrect or inconsistent water levels during wash cycles
- Water leaks around the valve or inlet area
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
1 water leaking on the floor at left side and 2 occasionally tub filling a number of inches when sitting Kenneth S. • San Carlos , CA • April 15, 2016
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure...
Read more
More
$79.95
- Compare At:
-
$95.14
- You Save:
-
$15.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 203956
The Damper Pad Kit is an OEM part for Whirlpool washing machines. The kit includes three specially designed pads made of durable materials. These pads effectively dampen vibrations, providing cushioning and stability to minimize noise and ensure a smoother operation of the washing machine. Additionally, the kit includes three tubes of poly-lube grease. This grease lubricates the contact points between the damper pads and the machine's framework.
Causes of a faulty damper pad kit can include wear and tear over time, damage due to heavy loads or mishandling, or degradation of the pads and lubrication.
Symptoms of a bad damper pad kit may include:
- Excessive noise or rattling during washing or spinning
- Increased vibrations or movement of the washing machine
- Visible wear or damage to the existing pads
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
May tag washer bumper pads wore out Larry W. • Hookstown , PA • November 18, 2014
I ordered parts from appliance parts pro at 3:30 on Friday and they were delivered at bout noon on Saturday the next day. Took the machine apart removed the old pads. With the directions in the packages put it back together and the wife ran 5 loads of clothes through it. Works great. Was awesome to get the parts so quick
Read more
More
$33.95
- Compare At:
-
$42.01
- You Save:
-
$8.06
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003441
The OEM Replacement is a bearing designed to function as the rear bearing in Whirlpool front-load washers. It also works as the upper brake bearing in top-load washers. Positioned near the tub's brake assembly, this component plays a significant role in the operation of the washer. In top-load washers, it resides above the brake assembly.
Causes of a bad bearing can include prolonged wear and tear, exposure to excessive loads, or water intrusion that leads to rust and corrosion. A compromised bearing can lead to more significant issues if not addressed promptly.
Symptoms of a bad bearing include:
- Loud, unusual noises during the wash or spin cycles
- Excessive vibration or movement of the washer
- The drum not rotating smoothly or becoming stuck
- Leaks around the drum area
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Noisy spin cycle Gregory E. • Halifax , PA • April 17, 2017
I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will...
Read more
More
$17.95
- Compare At:
-
$21.18
- You Save:
-
$3.23
Genuine Whirlpool part
By: Whirlpool
Part Number: W10841140
This OEM Replacement Part is an Adhesive designed for use in high-temperature areas of your Whirlpool appliances. Approximately 7.5 inches long, this white adhesive is suitable for securing parts such as grate feet, gaskets, and felt seals. It is especially useful, particularly in hot zones like a cooktop. The heat-resistant properties of this adhesive ensure that the bond integrity remains uncompromised even under high-temperature conditions.
Contained in a 3oz bottle, this adhesive forms a resilient bond between various components. It is commonly used in conjunction with gaskets, felt seals, and rubber feet. The RTV high temp silicone adhesive/sealant guarantees the safety and longevity of your appliance by ensuring a secure fit of parts exposed to high heat.
Do-It-Yourself Stories from Customers like You
My 20 year old maytag washer was knocking durring the wash cycle Dennis K. • Antioch , CA • November 15, 2015
I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the...
Read more
More
$17.95
- Compare At:
-
$21.18
- You Save:
-
$3.23
Genuine Whirlpool part
By: Whirlpool
Part Number: WP216201
The Injector Valve is an OEM replacement part specific to Whirlpool washing machines. It plays an important role in properly dispensing detergent into the wash load. Located inside the detergent dispenser drawer, the injector valve regulates the flow of water at timed intervals to fully dissolve and evenly distribute detergent among clothes. Washer air gap rubber injector. For the injector nozzle order WP213015. For a kit that includes the injector valve, nozzle, and two clamps order 12001677
Causes of a bad injector valve can include clogging from mineral deposits or debris, wear and tear from regular use, or damage from high water pressure. A malfunctioning injector valve can lead to improper water levels and affect the washing machine's performance.
Symptoms of a bad injector valve include:
- Inadequate water filling the washer
- Water leaks around the valve area
- Unusual noises during the water filling cycle
- The washer not advancing through cycles properly
- Visible debris or deposits at the injector valve opening
It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washers.
Do-It-Yourself Stories from Customers like You
1 water leaking on the floor at left side and 2 occasionally tub filling a number of inches when sitting Kenneth S. • San Carlos , CA • April 15, 2016
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure...
Read more
More
$19.95
- Compare At:
-
$23.94
- You Save:
-
$3.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596669
The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.
Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Leaks at the hose connection points
- Hoses slipping off the connections
- Visible rust or damage on the clamp
- Reduced appliance efficiency due to leaks
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not stop filling with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
My washing machine smelt horrible Bryan W. • Ogdensburg , NY • August 20, 2018
First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available....
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP213045
The Tub to Pump Hose is an OEM part for Whirlpool washing machines. This hose connects the tub to the pump, allowing water to drain from the tub during the washing and rinsing cycles. It is designed to handle the water flow and pressure within the washer, ensuring efficient drainage.
Causes of a bad tub to pump hose can include wear and tear over time, exposure to harsh chemicals or debris, or damage due to accidental punctures or kinks. When the hose is compromised, it can lead to drainage issues and potential water leaks.
Symptoms of a bad tub to pump hose include:
- Water not draining from the washer
- Leaks or puddles underneath the washer
- Visible cracks or wear on the hose
- Error codes related to drainage problems
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Leaking water from bottom of washer found hose cracked just below the tub Terry S. • Morgan Hill , CA • April 23, 2014
I replaced the hose between the tub and the pump. The clamp screws were quite rusted but I used a socket wrench on them since they have hex heads in addition to the screwdriver slot. If I had tried to use a screwdriver, I think it would have been difficult. I did not reuse the original clamps but replaced them with hardware store hose clamps.
Read more
More
$46.95
- Compare At:
-
$55.87
- You Save:
-
$8.92
Genuine Whirlpool part
By: Whirlpool
Part Number: 205000
The Motor Mount Roller and Spring Kit is an OEM part for Whirlpool washing machines. This kit includes the motor mount, roller, and spring, which work together to support and stabilize the motor during the wash and spin cycles. These components are crucial for minimizing vibrations and ensuring the motor runs smoothly and efficiently.
Causes of a bad motor mount, roller, or spring can include normal wear and tear over time, heavy or unbalanced loads that put extra stress on the components, and accidental damage or impact.
Symptoms of a bad motor mount, roller, or spring include:
- Excessive noise during the wash or spin cycle
- Vibrations or shaking of the washing machine
- The drum not spinning properly
- Motor misalignment or poor performance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not agitate
-
Burning smell
See more...
Do-It-Yourself Stories from Customers like You
Maytag clothes washer would not spin or drain Ben M. • Wallingford , CT • September 29, 2018
The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell.
At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer...
Read more
More
$48.95
- Compare At:
-
$58.25
- You Save:
-
$9.30
Genuine Whirlpool part
By: Whirlpool
Part Number: 206638
The Siphon Break is an OEM part for Whirlpool washing machines. It is a critical safety component that prevents the backflow of contaminated water from the washer into the fresh water supply line. For the gasket use part number [AP6005834], For the siphon elbow use part number [AP4024083]
Causes of a faulty siphon break include physical damage, clogging due to mineral buildup or debris, or general wear and tear over time.
Symptoms of a bad siphon break:
- Water leaks or puddles around the washing machine
- The washer not filling with water properly
- Potential for contaminated water to enter the fresh water supply
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.
Do-It-Yourself Stories from Customers like You
Syphonbreak was leaking James O. • Bryant , AL • September 04, 2015
We ordered parts from appliance parts pros and I fixed it.
Read more
More
$54.95
- Compare At:
-
$64.84
- You Save:
-
$9.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP207166
The Lid Check Switch is an OEM part for Whirlpool washing machines. It ensures the washer operates only when the lid is securely closed, providing a safety mechanism to prevent the machine from running with the lid open. This is the switch only. For the complete assembly including the switch order part number AP6006235.
Causes of a bad lid check switch can include wear and tear over time, damage from repeated use, or issues with the electrical connections. If the switch fails, it can prevent the washer from starting or interrupt the wash cycle.
Symptoms of a bad lid check switch include:
- Washer not starting
- Interruption of the wash cycle
- Error codes indicating lid issues
- Lid not locking properly
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not fill with water
-
Will not agitate
See more...
Do-It-Yourself Stories from Customers like You
My washer stopped it just sttoped working Charles T. • Houston , TX • February 01, 2015
First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you...
Read more
More
$44.95
- Compare At:
-
$53.49
- You Save:
-
$8.54
Genuine Whirlpool part
By: Whirlpool
Part Number: WP285655
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Water leaks around the hose connection points
- The hose slipping off the fitting
- Visible rust or wear on the clamp
- Difficulty in tightening the clamp to secure the hose
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Syphonbreak was leaking James O. • Bryant , AL • September 04, 2015
We ordered parts from appliance parts pros and I fixed it.
Read more
More
$9.95
- Compare At:
-
$11.74
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WP213015
This injector nozzle channels incoming water from the fill hose into the wash basket. Replacing a cracked or clogged nozzle helps stop leaks and restores a clean, controlled water stream during fill. What it does:
- Directs incoming water into the tub via the injector assembly
- Works with the injector cap to diffuse flow and reduce splashback/siphoning
- Maintains a proper spray pattern during fill
- Common symptoms include water leaking or spraying from the injector area, visible cracks, or mineral buildup restricting flow
What's included:
Install notes:
- Disconnect power and turn off water supply before servicing
- Access the injector assembly by removing the cabinet/top per your model's procedure
- Release the hose clamp, remove the old nozzle, and install the new nozzle oriented toward the tub; reinstall the injector cap if your model uses one, and secure the clamp
- Restore water and power, then run a test fill to check for leaks
Do-It-Yourself Stories from Customers like You
1 water leaking on the floor at left side and 2 occasionally tub filling a number of inches when sitting Kenneth S. • San Carlos , CA • April 15, 2016
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13