Cdc22p2aww Parts

This coupler and hose assembly connects your portable dishwasher to the sink faucet during operation. It supplies fresh water and returns drain water to the sink, helping stop leaks and restore reliable filling and draining.

• Provides a quick-connect link to a compatible faucet adapter for temporary hookup
• Carries incoming water to the dishwasher and routes drain water back to the sink
• Maintains a secure, leak-resistant seal during wash and drain cycles
• Replace if the coupler won't attach or stay on the faucet, hoses are cracked/kinked, or you see leaks and poor fill/drain performance

• Unplug the appliance and turn off water before service
• Verify the faucet adapter and O-rings are in good condition; hand-tighten only—do not overtighten with tools
• Route hoses to avoid kinks and sharp bends
• Open the faucet slowly and run a short test cycle; check all connections for leaks

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This replacement door handle restores a secure grip and normal door operation on compatible Whirlpool appliances. It provides a like-for-like fit and finish to replace a damaged, loose, or worn handle so doors open and close reliably. What it does:

• Replaces a broken, cracked, or missing door handle to restore normal use
• Provides a solid grip so the door opens and closes smoothly
• Matches the original mounting points for straightforward fit
• Helps eliminate rattling or loose-handle symptoms

• One replacement handle

• Intended to be installed with the original mounting screws and hardware; only included items ship
• Turn off and unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use moderate force when aligning the handle to avoid damaging trim or fasteners

Note: Check Serial Number for correct part

This float palnut is a push-on retainer that secures the dishwasher's water-level float to its stem. Keeping the float anchored helps the overfill protection work properly, supporting correct fill levels and helping prevent leaks from overfilling. What it does:

• Holds the float in position so it can move freely with water level changes
• Helps the float reliably actuate the overfill/float switch
• Replace if cracked, loose, or missing
• Typical symptoms include a loose or wobbly float, the float popping off, erratic filling, overfilling, or leaks near the float area

• One float palnut

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the float assembly
• Remove the old retainer; press the new palnut squarely onto the float stem until snug
• The float moves freely up and down before reassembling

This top spray arm, also called the top wash spinner, restores proper water distribution to the top of the tub. It helps deliver even spray coverage so glasses and dishes on the upper rack come out clean. What it does:

• Rotates under water pressure to spray jets across the upper rack area
• Improves wash coverage and rinsing for items on the top level
• Common failure signs: poor cleaning on the top rack, arm not spinning, clogged jets, or visible cracks/warping
• May also cause uneven spray patterns or debris buildup if the spinner is damaged

• 1 top spray arm

• Disconnect power at the breaker and turn off the water supply before servicing
• Open the door; remove the upper rack if needed for access
• Release the retainer or screw, remove the old spinner, and clear any debris from the hub/feed area
• Install the new spinner and ensure it spins freely before running a test cycle

This dishwasher impeller assembly mounts on the circulation pump and pressurizes wash water for the spray arms. Replacing a worn or damaged impeller restores proper spray pressure, cleaning performance, and quieter operation.

• Spins with the circulation motor to pressurize wash water
• Drives flow to the spray arms for effective wash action
• Typical symptoms: weak or no spray, poor cleaning results, grinding or rattling from pump area
• Often fails from broken vanes or debris; inspect filters/chopper while open

• Disconnect power and water before servicing
• Access is typically from inside the tub: remove the lower spray arm, filter screens, and cover to reach the impeller
• Note the order of parts and transfer any reusable hardware; replace worn O-rings/seals as needed
• Do not overtighten plastic parts; verify the impeller spins freely before reassembly and testing

Attaches to the inner tub for the upper rack

Pan-head screw used to secure panels, brackets and trim on Whirlpool appliances. Replacing a damaged or missing screw restores proper fastening to reduce vibration and keep assemblies aligned during operation. What it does:

• Secures panels, brackets and trim pieces to the appliance chassis.
• Stops loose panels from rattling, vibrating or shifting during use.
• Used when the original screw is stripped, corroded or missing.
• OEM replacement that restores the original fastening point.

• Unplug the appliance or shut off power before working on it.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug—do not overtighten or force in plastic parts.
• If the original hole or threads are damaged, inspect the surrounding area before reuse.

This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.

Color: White. This basket measures about 9 inches wide by 7 inches high by 6 inches deep. The cover and handle are not included. The cover is no longer available. For the handle order W11033847.

Dishwasher lower wash arm and spray tower support.

This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.

Long tub insulation that fits the appliance's inner tub, reducing operating noise and helping stabilize temperature around the tub for quieter, more consistent performance. Replaces worn or damaged insulation to address rattles and drafts. What it does:

• Dampens noise and vibration when insulation is torn, compressed or missing.
• Helps limit heat loss and reduce cold spots that can cause condensation or longer warm-up times.
• Reduces rattling or knocking caused by loose or degraded insulation.
• Intended for specific Whirlpool tubs—verify model fit before ordering.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove outer panels or drum components per the service manual; insulation may be held with clips, adhesive, or fasteners.
• Wear gloves and a dust mask—insulation fibers can irritate skin and lungs.

This spray arm retaining nut secures the dishwasher spray arm to its hub, keeping it aligned and spinning for consistent wash coverage. Replacing a worn or stripped nut restores spray performance and helps prevent the arm from detaching during cycles.

• Secures the spray arm to the hub/pump outlet so it rotates freely
• Helps maintain proper alignment and clearance to avoid rubbing or leaks
• Direct replacement for a cracked, loose, or stripped spray arm nut
• Common symptoms: poor cleaning, rattling noises, or the spray arm falling off

• Disconnect power and water supply; remove the lower rack for access
• Unscrew the old nut and lift off the spray arm; clean any debris on the hub
• Position the arm and thread the new nut by hand until snug; do not overtighten
• Spin the arm by hand to confirm free movement before running a test cycle