Dg6700228a Parts

This was a Maytag DE312 actually a Whirlpool labeled as Maytag) and is 27 years old. Replaced motor, drive belt and drum rollers. One tricky part was the motor because the new motor comes with integral starter and it was necessary to cut off existing female spade connectors on some wires and crimp on new connectors. Instructions were adequate but need to be carefully followed and a decent electrical stripping and crimping tool must be at hand. I bought a new motor drive pulley because another... Read more

I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more

• Little to no heat when baking
• Won't start

We replaced the broken Terminal Block but have not yet replaced the Control Panel. Will purchase that part from you shortly. Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

Replaced door strike and door latch Read more

Good Read more

I checked out a few youtube videos on trouble shooting a gas dryer that would not heat, like this one https://www.youtube.com/watch?v=Q8j6fQM3P34. Eliminated all the sensors as possible problems, leaving only the coils or more advanced problems. Took the chance it was one of the coils. I ordered both, replaced them both, put the dryer back together and fortunately that was the problem and it lit up and is running as good as new. Read more

I replaced the motor and all other moving components along with the felt drum seals.drum glides and drive belt. The wiring instruction is where i had the most problems. Because my wiring had only 4 wires in the harness not 5, and one was a different color then the instructions call out, I believe was because it might have been and older model. the instruction called for a gray wire but mine was white with a blue piggy back wire attached. but after finding a few videos on line i figured that the... Read more

• Door won't close

My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more

• Noisy

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

I checked out a few youtube videos on trouble shooting a gas dryer that would not heat, like this one https://www.youtube.com/watch?v=Q8j6fQM3P34. Eliminated all the sensors as possible problems, leaving only the coils or more advanced problems. Took the chance it was one of the coils. I ordered both, replaced them both, put the dryer back together and fortunately that was the problem and it lit up and is running as good as new. Read more

• Will not agitate
• Pumps but will not spin
• Will not tumble
• Noisy

Upon removal of the lower inspection panel on the front of the machine, my 20 year old son thought the motor was bad by the smell. But he did discover what turned out to be the belt tensioner pulley laying inside the machine. After he pronounced it dead, without a thought to the idler pulley, I looked at the machine and determined the lack of movement was due to the idler pulley having "fallen" off the shaft by looking at the illustrated parts break down provided on this website. Ordered the... Read more

• No heat or not enough heat

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

For several months we could smell a slight odor of propane in the laundry room and wondered why, just didn't seem like it was enough to be overly concerned, but thought something must be wrong with the dryer, but it was still working. We just didn't know how inefficiently. Then the extra time it took to dry a load of clothes progressively seemed to get longer, but things still seemed to work fine and the clothes got dried, given enough time. Then approximately 3 weeks ago we noticed the dryer... Read more

• Will not tumble

First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more

• Marks left on clothes
• Noisy

I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more