Du1005xtvq1 Parts

Protective rubber bumper for dishwasher dishrack. Installs on the outer front edge of the lower rack. Replace if cracked, broken, or missing.

Size: 8-32 x 1/4 inch.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Wire harness elbow connector for dishwashers. Replaces damaged, cracked, or broken electrical connectors that route power between components.

Upper dishrack assembly for dishwashers. Slides on tracks to hold dishes on the top shelf. Replace if cracked, rusted, broken tines, or no longer stable.

Keep utensils organized and secure during the wash. This dishwasher silverware basket replaces a cracked or missing basket so flatware stays upright for thorough cleaning, helps prevent small items from slipping through the rack, and streamlines loading. What it does:

• Holds silverware and small utensils in the rack throughout wash and rinse cycles
• Keeps pieces separated and upright to improve cleaning and drying performance
• Helps prevent loose items from contacting the spray arm or falling to the tub bottom
• Replace if the basket is cracked, warped, or missing sections, or if utensils tip over or come out dirty

• 1 silverware basket

• No tools required: slide out the rack, lift out the old basket, and set the new basket in the same location
• Ensure the basket is seated securely and does not interfere with spray-arm rotation
• Load knives and sharp items with points down; avoid nesting spoons for best results

Seals the pump housing to prevent water leaking from the tub onto the motor. Replace if you see leaks around the circulation pump area. Confirm fit by model.

includes seal

Seal gasket for dishwasher inlet base assembly. Replace if you notice leaks, moisture buildup, or debris entering internal components. Confirm fit.

Dishwasher won't drain or overflows? A missing or worn check ball can cause backflow issues. This small part maintains one-way water flow in the valve.

This door catch and strike work together to keep the door securely closed and engage the safety interlock switch. Replacing worn pieces restores a firm latch and reliable operation when the door is properly shut.

• Aligns and engages the latch so the door stays closed during operation
• Activates the door switch so cycles can start
• Helps prevent the door from popping open mid-cycle
• Common symptoms: door won't latch without force, unit won't start, visible wear or a bent strike

• Disconnect power to the appliance before servicing
• Open the door and remove mounting fasteners to swap the catch and strike
• Adjust strike alignment/depth so the latch engages fully and the door sits flush
• Restore power and test for smooth closing and proper cycle start

Secures knobs, trim, or linkages to shafts inside your dishwasher. Replace if broken, cracked, or missing to prevent components from loosening.

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair

Screw for wash impeller.

Replacement lower dishrack wheel for dishwashers. Installs on the bottom rack to enable smooth rolling. Replace if wheel is cracked, broken, or worn.