Du8300xx-3 Parts

Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.

The Actuator is an OEM part for Whirlpool dishwashers. This actuator is responsible for releasing detergent from the dispenser at the appropriate time during the wash cycle, ensuring effective cleaning of the dishes.

Causes of a bad detergent dispenser actuator can include electrical malfunctions, wear and tear from frequent use, or physical damage to the actuator mechanism.

Symptoms of a bad detergent dispenser actuator include:

• The detergent not dispensing during the wash cycle
• The dispenser door not opening
• Dishes not being cleaned properly due to no detergent release
• Error codes related to the dispenser

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This base heater assembly restores the oven's lower heating function in select convection microwaves. It delivers bottom radiant heat for baking and crisping so the unit can preheat properly and brown foods evenly.

• Supplies bottom heat during convection, bake, or crisp cycles
• Works with the control and temperature sensor to reach and maintain set temperature
• Common symptoms of a failed heater may include no heat in convection mode, very long preheat, or poor browning/crisping
• Visible damage to the element or tripping a circuit breaker may also indicate a shorted heater

• Disconnect power before servicing. Microwaves contain high-voltage components that can retain a charge even when unplugged
• Allow the unit to cool completely; access typically requires removing the outer cover or lowering an over-the-range unit
• Note wire locations and routing before removal; transfer any brackets, shields, or screws from the original assembly
• Route wires exactly as original and avoid pinching; confirm clearances before reassembly and test a convection preheat

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This thermal fuse protects your appliance by opening the circuit if temperatures climb beyond a safe limit, helping prevent wiring or control damage. When it blows, the unit may lose all power or stop mid-cycle. What it does:

• Cuts power when overheating is detected to protect internal components
• Helps prevent damage from shorted heaters, motors, or wiring faults
• Common symptoms: no power, won't start, shuts off during operation, no lights/display
• A blown fuse reads open (no continuity) and must be replaced—it is not resettable

• 1 thermal fuse

• Disconnect power before servicing to avoid electrical shock
• Access the fuse location per your model's service information; note wire orientation and mounting
• Replace one-for-one; do not bypass or up-rate the fuse. Identify and correct the overheating cause before restoring power.

Dishwasher door panel insert. Reversible: white color on one side, black on the other.

Color: Black. Other colors: For white use WP3369614.

The Impeller is an OEM part for Whirlpool brand dishwashers. Located within the dishwasher sump assembly, this plastic component utilizes rotating blades to circulate wash water throughout cycles.

Causes of a bad impeller can include cracking or damage from minerals over time, chunks of food debris jamming the blades, or normal wear on plastic.

Symptoms of a faulty impeller include: 

• Inadequate water circulation yielding poor cleaning 
• Food particles or utensils not fully rinsed
• Loud clicking or grinding noises mid-cycle
• Error codes relating to low water pressure

Replacing the impeller restores optimum water flow for Whirlpool dishwashers. Proper circulation using the OEM replacement ensures all portions of dishes and cycles receive sufficient water volume. Compatibility also includes Maytag, Jenn-Air, Amana, Magic Chef, and other brands.

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

Pump housing only. For a complete pump and motor assembly, order WPW10247394.

This upper draw bar is a door-latch linkage piece used in dishwashers. It connects the handle/actuator to the latch mechanism so the door closes securely and the door switch engages, allowing the cycle to start reliably.

• Links the door handle/actuator to the latch for positive closure
• Helps ensure the door switch is engaged so the unit will run
• Restores proper latch alignment and handle feel
• Common symptoms: door won't latch or pops open, dishwasher won't start, must push/hold door to run, loose or floppy handle

• Disconnect power at the breaker; turn off water supply if working near the inlet
• Open the door and remove inner-door screws to access the latch linkage
• Note bar orientation; transfer any clips/bushings and reuse existing hardware
• Reassemble and check latch engagement before running a cycle

Almond. Size: 13 oz. can. Acrylic appliance paint.

Color: Almond

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning