Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more
Supports your refrigerator at the base and lets you roll it forward for cleaning. Replace this roller assembly if cracked, broken, or seized to restore smooth movement.
I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The... Read more
Mounting bracket that secures the ice maker assembly to the refrigerator wall. Replace if cracked, broken, or missing to restore proper ice maker support.
Replaced the ice maker. The kit came with everything I needed to replace the ice maker. Parts that did not come with the kit were re-used from the old one. My Whirlpool refrig/freezer is an older model so the wiring harness that came with the kit was different from my existing. So instead of disconnecting the ice maker wiring harness from the freezer, I had to disconnect the harness at the ice maker. That was a b..... Anyway after about 20 minutes, finally unhooked the connector. I had... Read more
If your freezer is icing up or coils are freezing, replace the defrost heater. Melts frost from evaporator coils during defrost cycle. DIY-friendly repair.
I replaced the defrost control and heater just to be sure. I usedmthe helpful video and though it took me 2 hours i gotmit done and saved hundreds Read more
1/4 inch compression nut for securing plastic water lines in refrigerators and ice makers. Replace worn, cracked, or missing nuts to prevent leaks.
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Secures the bottom grille to your refrigerator frame. Replace if the original clip is cracked, broken, or missing and the grille won't stay in place.
Did research on line and figured it was valve inlet part. The helpful video you provide made me realize that it was an easy job to complete. Yes it was easy because of the video and the part was exactly what was needed. We saved money by doing it ourselves. So while we were on the order site we ordered the brackets for the front grill. The old ones snapped off a long time ago. Again helpful video on your site on how to do the replacement ourselves. We now have water pressure back and that... Read more
Replacement support stud that holds refrigerator shelves securely in place. Needed when original peg is broken, cracked, or missing from shelf wall.
Myself Read more
Flexible narrow brush reaches under and behind refrigerator cabinet to clean condenser coils and vents. Replace worn or missing brush to remove dust buildup.
Replaced bad condenser motor Read more
This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.
After being told by a service repairman that it would cost me close to $200 to repair, I resolved to just not use the dispenser. After about a year, I had decided that I wanted to repair it and would look at the options myself. At the least, I could figure out which parts were needed to repair it and have them on hand for a service guy if I determined I could not do the job myself. The more I studied it, the more I felt confident that I could do it, and sure enough, when the part arrived - a... Read more
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Replaced It With New One Read more
White plastic cap that secures the water filter in place. Replace if cracked, broken, or missing to properly hold your refrigerator's filter cartridge.
Replaced with new one from your website. I love the website because it shows you how to fix your problem before you get started. I Read more
Pan head screw secures panels, brackets, and trim on refrigerators and freezers. Replace missing, stripped, or damaged screws to restore proper fastening.
Looked up model on your website. You had all the parts I needed, numbered and visually shown. Perfect! Read more
Clear plastic egg container that sits on refrigerator shelves. Replace your cracked, broken, or missing egg holder to keep eggs organized and secure.
Ordered a replacement part from your on line store. Read more
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
Plastic stud secures refrigerator shelves to interior liner walls. Replace if broken, cracked, or won't stay in place. Twists into liner holes.
Watched your youtube video which was awesome and then knew how to take it out without breaking the side of fridge it went into and there was a link to the part in the video so I ordered it and it came right away and it fixed it, shipping seemed a little much though but I was very satisfied overall Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.