Ed5fhaxsq Parts

This replacement ice auger fits inside the freezer ice bin and rotates to move ice to the dispenser and through the crusher, restoring consistent cubed or crushed ice dispensing when the original auger is bent, stripped, or broken.

• Moves ice through the bin to the dispenser chute
• Works with the crusher blades/selector for crushed or cubed dispensing
• Common symptoms: no ice dispensed, motor runs but ice doesn't move, slow or jammed dispensing, grinding noises from the bin
• Replaces a bent, worn, or broken auger spiral that fails to engage or feed ice

• Disconnect power; remove the ice bin from the freezer/door
• Empty the bin; carefully disassemble the crusher blade stack, noting the exact order of blades, spacers, and washers (take reference photos)
• Transfer components onto the new auger and secure the retaining hardware; verify smooth rotation before reinstalling
• Wear cut-resistant gloves—crusher blades and edges are sharp

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing

This water dispenser lever is the paddle you press on your refrigerator's dispenser. Replacing a worn paddle restores smooth activation of the water dispenser and refreshes the look of the dispenser area with a matching Biscuit finish.

• Provides the paddle you press to activate the water dispenser
• Transfers your push to the internal dispenser switch to start water flow
• Common symptoms of a failed lever: cracked/broken paddle, sticking or loose action, or no water dispensing when pressed
• Biscuit color for a seamless, factory-matched appearance

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser front panel/trim to access and release the lever
• Transfer existing pivot hardware or springs from the original lever, if applicable
• Reassemble, restore power/water, and test for smooth operation

This 5SP start device engages the refrigerator's compressor at power-up and helps safeguard it during startup. Replacing a weak or failed start device can restore cooling and eliminate repeated clicking or brief humming from the compressor. What it does:

• Works in the compressor start circuit to help the compressor start and then disengage from the run circuit
• Helps protect the compressor during hard-start conditions
• Typical failure symptoms include no cooling, compressor not running, rapid clicking, or a brief hum followed by shutoff
• Show heat damage or discoloration at the connector or housing

• Disconnect power and allow the compressor area to cool before servicing
• Access the compressor compartment; note/photograph wire positions, unplug the harness, and pull the device straight off the compressor pins
• Inspect compressor terminals and the harness connector; repair any burnt or loose terminals before installing the new device
• If your model uses a separate run capacitor, transfer and reconnect it exactly as before; fully seat the new device on the compressor pins and restore power

This bin button is a small snap-in component used on refrigerator storage bins. It helps secure and align the bin so it seats properly and operates smoothly, restoring a tight fit when the original button is cracked, worn, or missing.

• Snaps into a designated opening on the bin or cabinet liner to act as a support/stop
• Keeps the bin aligned and secured during everyday use
• Replaces a damaged or missing button that can cause wobble, binding, or the bin to fall out
• Restores proper fit and smooth operation of the affected bin

• Disconnect power and remove items from the affected bin
• Remove the bin; pry out the damaged/missing button from its seat
• Align and press the new button fully into the opening until secure
• Reinstall the bin and check for smooth, secure operation

This refrigerator ice auger sits inside the ice bin and rotates to move cubes or crushed ice toward the chute. Replacing a worn, bent, or stripped auger restores smooth, consistent dispensing performance. What it does:

• Rotates inside the ice bin to feed ice toward the crusher and dispenser chute
• Helps deliver either cubes or crushed ice depending on the selector
• Common symptoms: dispenser motor runs but no ice comes out, weak/intermittent dispensing, frequent ice jams, or grinding noises from the ice bucket

• 1 ice auger

• Unplug the refrigerator before servicing; remove and empty the ice bin
• Note the order of internal parts during disassembly; transfer any reusable hardware from the original assembly
• Wear cut-resistant gloves—metal and plastic edges can be sharp
• Reassemble so the auger turns freely by hand, reinstall the bin, restore power, and test the dispenser

Pan-head screw used to secure panels, brackets and trim on Whirlpool appliances. Replacing a damaged or missing screw restores proper fastening to reduce vibration and keep assemblies aligned during operation. What it does:

• Secures panels, brackets and trim pieces to the appliance chassis.
• Stops loose panels from rattling, vibrating or shifting during use.
• Used when the original screw is stripped, corroded or missing.
• OEM replacement that restores the original fastening point.

• Unplug the appliance or shut off power before working on it.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug—do not overtighten or force in plastic parts.
• If the original hole or threads are damaged, inspect the surrounding area before reuse.

This water tube bracket secures the refrigerator's water supply tube along the cabinet or door route. Replacing a damaged bracket helps prevent kinks and leaks and maintains reliable water flow to the dispenser and icemaker.

• Holds and guides the water tube so it stays correctly positioned
• Helps prevent kinks, rubbing, and vibration that can lead to leaks
• Supports consistent water flow to the dispenser and icemaker
• Typical signs of failure: cracked or missing bracket, tube slipping or dangling, recurring kinks, dampness/leaks along the tubing path

• Unplug the refrigerator and shut off the water supply before servicing
• Access the bracket location (often in a hinge or cabinet routing area; varies by model)
• Release the tube, remove the old bracket, and install the new bracket; reuse existing hardware
• Restore water and power, purge air from the line, and check for leaks and dispenser/ice operation

This tube routes household water into the refrigerator's filter housing. Replacing a cracked, pinholed, or kinked tube restores reliable water flow and helps prevent leaks around the water filter area.

• Carries water from the inlet valve to the filter housing
• Maintains a sealed path under line pressure; damage can cause leaks or reduced flow
• Common symptoms: leaking near the filter/base grille, slow or no dispenser flow, or no ice production
• Visible cracks, pinholes, kinks, or brittleness indicate the tube should be replaced

• Unplug the refrigerator and shut off the water supply
• Dispense water to relieve line pressure; place a towel to catch residual water
• Note tube routing; fully seat tube ends in fittings and secure any retainers/clips
• Restore water and power, then check all connections for leaks and flush the system

Water tube connector that joins two sections of a refrigerator's water tubing for a secure, leak-resistant connection. Replacing a cracked or leaking connector can help restore consistent water flow to the dispenser and ice maker.

• Connects two lengths of refrigerator water tubing in the supply, filter, dispenser, or ice maker circuit
• Helps maintain a sealed connection to reduce leaks and air intrusion
• Common symptoms of failure: dripping at the fitting, water under the unit, weak/no dispensing, or ice maker not filling
• Replace if the connector is cracked or will not hold tubing securely

• Unplug the refrigerator and shut off the water supply
• Dispense water to relieve line pressure; place a towel under the connection
• Cut tube ends square; push each tube fully into the connector until seated, then tug gently to confirm engagement
• Restore water and check carefully for leaks before reconnecting power

This light socket replaces a worn or heat-damaged lamp holder so your appliance light works reliably again. Its straight-connector design fits applications with in-line wiring, ensuring a secure electrical connection to the interior light bulb.

• Holds the light bulb and supplies power to it
• Restores interior illumination for better visibility
• Straight terminal orientation for housings requiring inline wiring clearance
• Typical signs of failure: light stays off with a good bulb, flickers, or shows heat damage at the socket

• Disconnect power at the breaker or unplug before servicing; allow the area to cool completely
• Remove any lens/cover; transfer wires one at a time to maintain correct connections
• Secure the socket with existing bracket/fasteners; do not overtighten
• Test light operation before reassembly and confirm the door switch activates the light

This freezer bin replaces a cracked, broken or missing storage bin to restore organized storage and keep frozen items contained. Durable replacement designed for direct-fit installation in compatible freezer compartments. What it does:

• Holds and organizes frozen food so items don't fall into lower compartments
• Replaces cracked, split or warped bins that can allow items to shift or block drawer movement
• Helps restore smooth sliding and proper storage space in the freezer compartment
• Fits into existing bin tracks or rails to maintain normal drawer operation

• Unplug the appliance or disconnect power before beginning any work
• Empty the freezer section and remove the old bin by sliding it out of its tracks
• Slide the replacement bin into the same tracks until it snaps or seats fully; some models may use simple clips or stops
• Your refrigerator's owner manual or parts diagram for model-specific removal and reassembly guidance

This replacement screw secures appliance panels and internal components. Installing a correct OEM fastener restores a tight fit, reduces rattles and vibration, and helps keep assemblies aligned so your machine operates smoothly.

• Fastens brackets, panels, ducts, or housings to the cabinet or frame
• Replaces missing, stripped, or corroded hardware
• Helps stop rattles, vibration, and loose or misaligned parts
• Maintains proper alignment for reliable operation

• Disconnect power; shut off gas and water before servicing
• Match this screw to the original location and hardware type used on your model
• Start threads by hand to avoid cross-threading; use the correct driver
• Snug only—do not overtighten, especially into plastic or thin sheet metal

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This emitter cover is the molded housing that shields and positions the infrared emitter for the refrigerator's ice level optics. Replacing a cracked or missing cover helps protect the board and keep the beam path clear for reliable ice making. What it does:

• Shields the emitter board and lens from moisture, frost, and debris
• Aligns the infrared beam path across the ice bin to the receiver
• Helps secure and position the ice level optics assembly
• Common symptoms: broken/missing cover, intermittent or no ice production due to optics misalignment or obstruction

• 1 emitter cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the optics components
• Release the old cover's retaining tabs or fastener and lift it off; avoid touching board components
• Position and secure the new cover, then restore power and test ice maker operation