Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.
I determined that it was a problem that occurred during the defrost cycle by resetting the GFCI outlet and forwarding the defrost timer until the defroster came on. Once the defrosting began, the GFCI outlet would reliably trip. I took apart the shielding inside of the freezer and tested the defrosting without the heating element or the thermostat connected. Since that looked good, I tested for proper functionality of the thermostat by removing it, placing it in a working freezer, and checking... Read more
Idler spring attaches to the idler arm to maintain proper belt tension. Replace if spring is broken, stretched, or missing to restore correct tension.
I encountered a high pitched squeal and loud rumbling. I figured the sounds were likely the rollers despite not matching other sounds on the repair videos for other dryers. The repair video for dryer rollers on AppliancePartsPros.com is of little use until Minute 2:56 because this Electrolux 517 model uses mostly Phillips head screw to fasten the front and top panels in place. You may find one latch at the top front center that holds the top and front panels in place. After unplugging the... Read more
Fix a dryer that won't shut off automatically or has temperature control issues. This thermistor sensor monitors heat levels for proper cycle operation.
I replaced the thermostat. The bearing on the motor was getting loose, so I changed the motor to. The repair took about 2 hours. There are some good re[air videos on the parts web site. Read more
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Fix dryer heating issues with this thermistor temperature sensor. Solves intermittent heat, cycle errors, and poor drying. Easy DIY repair.
Replaced all sensors, limiters, thermistors, thermostat. Works great now. Read more
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replaced clamp with a new one Read more
Dryer not heating? A failed igniter won't light the gas burner. This glow-bar igniter heats up to ignite gas during each cycle. Moderate DIY repair.
M5 x 0.8 metric machine screw secures panels and internal assemblies. Replace missing, stripped, or damaged fasteners to restore tight fit.
Ordered new hinge and outer and inner door. Super easy to fix and the repair video made it simple and easy! Very pleased! Fast shipping! Read more
Seals the dryer door to contain heat and prevent air leaks. Replace if torn, cracked, or causing poor drying performance. Confirm fit with your model.
The fix involved pulling the top of the dryer off, removing the front and replacing the gasket. You will need to scrape the old gasket off carefully with a dull putty knife. Make sure you order high temp adhesive or find a similar adhesive for the new gasket. Read more
Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.
Replacing door switch. Read more
Fastens panels, brackets, and internal components in your dryer. Replace stripped, rusted, or missing screws to restore secure mounting and alignment.
Screwed it on. The order shipped out the same day, arrived fast and on time. But I have to mention the customer service. The person helping me place the order was EXCEPTIONAL!!!! Very friendly and helpful. BEST customer service experience I’ve ever had. I was so impressed that I asked to speak to her manager. The manager was also exceptional. Very nice. I highly recommend this company. Read more
Small spacer that fits on the idler assembly shaft to properly align the belt tensioner. Replace if worn, cracked, or missing to maintain proper spacing.
Reviewed items that might be the issue and ordered them. After installed noise was gone. Read more
Dryer won't heat? A faulty gas burner assembly prevents proper flame and ignition. This part restores heat for efficient drying. DIY repair in 1-2 hours.
Went to youtube and found out what was the cause. Replaced the parts that said might be the issue, Dryer working perfectly. All done in about 1/12 hrs Read more