Elite He3 Washer Parts

• No heat or not enough heat
• Takes too long to dry

Our 25-year-old Whirlpool dryer abruptly stopped producing heat, though it was otherwise running normally. The unit had never required service of any type and we were reluctant to replace it. After confirming that no circuit breakers had tripped, I reviewed the Whirlpool and AppliancePartsPro websites and concluded that the most likely causes of the problem were a failed heating element and/or thermal fuse. I ordered both (they arrived in two business days), installed them and the dryer... Read more

• Marks left on clothes

Maytag Gas Dryer Model: MGDE300VW1 I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow! Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts... Read more

• Will not tumble

I did a little research and found out that the dryer drum rollers needed to be replaced. I decided that since I would be replacing the 4 drum rollers that I should replace the belt and the belt drive pulley. This was a simple project thanks to YouTube. I used one of appliancepartspor videos to st me through the repair. Now I have a dryer that does not squeal like a pig! Read more

After I came from from work, my wife told me about the problem. I quickly began to research the code F10 which according to the paper in the pouch behind my range said it needed a new temperature control sensor and that should fix it. It also said that if that doesn't fix the problem that I'd have to replace the circuit board which probably got fried due to the runaway temperature. So, I decided to just order the temperature sensor part# AP3963654 for $25.63 plus shipping. I ordered the part at... Read more

• Takes too long to dry

My fiance was involved in a very nasty divorce where a very biased female judge forced him from his home for 14 months before he could take up residency again. He brought me back with him and I witnessed the grotesque damages she intentionally inflicted on his property. His washer and dryer are very expensive and high-end, as is the home and all his contents. One of the many damages she caused was that she had not cleaned the dryer lint filter in 14 months and the lint was a thick carpet which... Read more

• No heat or not enough heat

I replaced the "heating element" which was bad.........as well as the "Thermst-fix" and "Thermal Cutoff" which are located on the side of the element mounting location while I had the dyer all opened up and the element mounting tube removed.......I also replaced the Dryer Thermister which is located on the top of the blower fan.....To get to these parts, you must open the top of the dryer which has spring latches on both sides of the front corners... they need to be pressed in (use a putty... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start

One day, while trying to roast chicken on the convection roast setting, my Electrolux oven stopped heating properly. I tried the broil setting and the top electric heating element worked fine. I then tried the bake setting and found that the bottom element wasn't working at all. I Googled the problem. The info I found said that the issue was probably that the bake element needed to be replaced. It said to look for a break or burned through spot on the element. If it appeared OK, remove it... Read more

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Element will not heat

Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros. Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

Replaced ignitor. Very simple project. Read more

Replaced the temperature sensor Read more

I have used this site before to fix my dishwasher, so I knew to check here first. I searched other's comments to troubleshoot my problem. Ordered the part and it arrived in only a couple of days. I should insert here that I am a 45 yo female, so if I could do this, anyone can. I watched the video and proceeded to replace the part. For my particular model, I didn't access the part from the back, but instead through the underside by removing the bottom drawer. Total from start to finish... Read more