Fafw4011lwo Parts

This front shock absorber kit stabilizes the washer's tub during spin to reduce vibration and noise. Replacing worn dampers helps restore smooth operation and protects the cabinet and suspension from excessive movement.

• Dampens and controls tub movement during wash and spin
• Helps reduce shaking, "walking," and loud thumping/banging noises
• Can help when the washer won't reach or maintain full spin due to imbalance
• Replaces weakened or damaged front shock mounts/dampers

• Disconnect power and water before servicing
• Access shocks per your model's procedure; support the tub to relieve load
• Install with mounts aligned and fasteners tightened securely; verify free tub movement
• Many replace shocks in pairs to maintain balanced damping

This tub filter screens wash water as it leaves the outer tub, capturing lint and small items before they reach the drain pump. Replacing a damaged or missing filter helps restore proper draining and protect the pump from debris.

• Screens lint, threads, and small debris from water exiting the tub
• Helps prevent drain pump clogs and drain-related errors
• A clogged, damaged, or missing filter can cause slow/no drain, standing water, or pump noise
• Physical damage, broken tabs, or warping are common reasons to replace

• Disconnect power and turn off water; expect residual water—use towels or a pan
• Access location varies by model; the filter sits at the outer tub outlet along the drain path
• Release the hose clamp/retainer, remove debris and the old filter, seat the new filter fully in the port
• Reattach clamps securely and run a short drain/rinse to check for leaks and proper flow

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Dispenser to Tub Hose is an OEM part for Frigidaire washing machines. This hose is responsible for transporting detergent and other cleaning agents from the dispenser to the tub during the wash cycle.  

Common causes of a bad hose include constant exposure to water and detergent, which can lead to wear and tear, blockages from detergent buildup, or physical damage such as cracks and splits.

Symptoms of a bad dispenser to tub hose include:

• Water leaks near the detergent dispenser
• Uneven or insufficient distribution of detergent
• Visible cracks, splits, or other damage to the hose
• Error codes on the washing machine related to water flow

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Cover is an OEM part for Frigidaire washing machines. This cover marks the location and type of detergent, bleach, or fabric softener to be used, ensuring proper distribution during the wash cycle. It provides clear guidance for correct detergent placement, contributing to optimal washing performance.

Causes of a bad cover can include wear and tear over time, damage from harsh cleaning agents, or physical impact resulting in cracks or faded markings.

Symptoms of a bad dispenser drawer compartment cover include:

• Faded or illegible markings
• Detergent not dispensing correctly
• Leaks or spills around the dispenser area
• Visible cracks or damage to the cover

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This O-Ring creates a tight, leak-resistant seal between appliance components. Replacing a worn or flattened ring restores proper sealing, helps stop drips at the joint, and protects nearby parts from moisture and mineral residue.

• Provides a compression seal between fittings, housings, or tubes
• Helps prevent water leaks and loss of pressure at the connection
• Common signs of failure: moisture or residue around the joint, visible cracks/flattening, leaks after reassembly
• Regular wear, heat, chemicals, or age can harden or deform the ring

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; lightly lubricate the new O-ring with food-grade silicone grease
• Seat evenly without twisting or pinching; reassemble and check for leaks

This motor control board regulates the washer's drive motor, managing speed and direction for tumble and spin cycles. Replacing a failed board helps restore drum movement and consistent cycle performance when the motor no longer responds. What it does:

• Controls drive motor speed and direction during wash and spin cycles
• Executes motor start/stop commands from the main control
• Failure can cause no spin, no tumble, or intermittent drum movement
• Trigger motor-related fault codes on some models

• Includes: 1 motor control board

• Disconnect power before servicing; observe ESD precautions when handling the board
• Access the control board per your model's service manual (typically in the base or rear cabinet area)
• Transfer wire connectors one at a time to the new board; ensure each is fully seated and latched
• Mount securely, reassemble, and run a diagnostic or spin test to verify motor operation

This is a dispenser inlet gasket intended for use on washing machines. This part ensures that the hot and cold water lines do not leak at the point where they are connected to the appliance. If the washing machine is leaking, the gasket may need to be replaced.Replacing a dispenser inlet gasket in a washing machine can be done easily. Screwdrivers and pliers are required. Disconnect the appliance before starting the repair. Wear work gloves for safety. The hot and cold water lines should both be turned off and removed to prevent flooding.This dispenser inlet gasket is an authentic OEM replacement part. It is sourced from the manufacturer. The replacement component is made of high-quality materials. It can be installed in several different models of washing machines. The dispenser inlet gasket is compatible with appliances produced by Frigidaire, Gibson, Electrolux, Westinghouse, and Kelvinator brands.

This replacement washer door window restores a clear view into the tub on compatible front-load models and helps the door seal correctly. Replace a cracked or cloudy pane to reduce leaks and keep operation safe. What it does:

• Provides the transparent viewing window in the washer door
• Works with the door boot/gasket to help form a watertight seal when closed
• Replace if the glass is cracked, chipped, shattered, or excessively scratched/cloudy
• Common symptoms include water leaking from the door area, poor sealing/door won't close, or visible damage to the window

• One door window glass

• Disconnect power and turn off water supply before servicing
• Wear cut-resistant gloves and eye protection; handle broken glass carefully
• Support or remove the door to a flat surface; separate door halves and transfer the window, noting orientation
• Clean the door boot sealing surface; seat the new glass evenly and reassemble without pinching the gasket; test for leaks

This replacement water inlet valve regulates water flow from the household supply into the washer. It restores proper filling and rinsing when the original valve leaks, sticks, or fails to open.

• Opens and closes to control water entering the dispenser/tub as directed by the control
• Helps maintain correct fill levels and flow during wash and rinse cycles
• Typical symptoms: no fill, slow fill, leaking at the valve, or water continuing to fill when off
• Often required when valve coils test open/short or mineral buildup causes the valve to stick

• Disconnect power and turn off both water supplies before servicing
• Place towels to catch water; relieve line pressure and label hoses/connectors for reassembly
• Transfer any mounting hardware from the old valve if needed; do not overtighten fittings
• Restore water and power, then run a fill cycle and check all connections for leaks

This metric machine screw features an M5 x 0.8 thread used to secure panels and assemblies inside your appliance. Replacing missing or damaged hardware restores a tight, rattle-free fit and helps maintain proper alignment of parts.

• Fastens appliance components using an M5 x 0.8 machine-thread
• Replaces missing, loose, or stripped screws
• Helps reduce vibration and rattling noises
• Maintains correct alignment of brackets, panels, or internal assemblies

• Disconnect power before servicing; if working near water connections, shut off the supply.
• Match thread and length to the original screw and replace in the same location.
• Start threading by hand to avoid cross-threading; use the correct driver and do not overtighten.
• Reinstall any original washers or lock hardware used with the screw.

This component is a drive motor that is made specifically for washing machines. The drive motor is what spins the tub and drives the agitator.If the washing machine fails to start or makes strange noises, it could be the drive motor that is causing the issue. Other signs that this part is faulty are if the washing machine fails to fill with water, agitate, spin, or drain. An error code reading “E57”, “E58”, “E59”, or “srv cll” may also appear on the digital display. Make sure to disconnect the appliance from its power source prior to attempting to replace this part. Whoever is performing the replacement may choose to wear gloves to protect their hands during this process.This drive motor is compatible with washing machines that are manufactured by Whirlpool, Kenmore Elite, Electrolux, Frigidaire, Crosley, and Kenmore. It is sold individually and sourced from the manufacturer itself.

This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.

• Holds a hose firmly on a pump, tub, dispenser, or valve outlet
• Maintains clamping force to help minimize leaks at the joint
• Helps keep hoses from slipping off during operation
• Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp

• Disconnect power and shut off water supply before servicing
• Place a towel or pan to catch residual water at the connection
• Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
• After reassembly, run a short cycle and check for leaks

Plastic door cover

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening