Ffld2426tw2a Parts

If your washer won't agitate or spin properly, the transmission may have failed. This mechanical component engages the drum during wash and spin cycles.

Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

This washer agitator mounts in the tub of top-load models and creates the back-and-forth wash action that moves clothes through water and detergent. Replacing a cracked or loose agitator restores turnover and cleaning performance.

• Produces the oscillating motion that circulates clothes during the wash cycle
• Transfers drive from the shaft/hub to move laundry through water and detergent
• Restores proper load turnover for effective cleaning
• Can help resolve: washer not agitating, weak/slow agitation, poor cleaning, wobbly/noisy agitator, or visible cracks/broken fins

• Disconnect power and turn off water before servicing
• Remove the softener dispenser/cap and center bolt/retainer; lift out the old agitator
• Inspect and transfer any reusable cap or hardware to the new agitator
• Align and seat the new agitator on the drive hub; tighten the fastener per manufacturer guidance and test

Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

Dryer won't heat? A faulty gas burner assembly prevents proper flame and ignition. This part restores heat for efficient drying. DIY repair in 1-2 hours.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Adjustable leveling leg that mounts underneath your laundry center to balance and stabilize the unit. Replace if cracked, bent, or missing threads.

Oven burner distributes gas and air mixture for even baking flames. Replace if rusted, corroded, or producing uneven flame patterns in your range.

This safety thermostat is a temperature-sensitive switch that helps protect your appliance from overheating. When excessive heat is detected, it opens the circuit to stop power to critical components, helping prevent damage and ensuring safe operation.

• Monitors temperature at a specific location and interrupts power if it exceeds a safe limit
• Can cause no power, no heat, or shutdown during use when failed or tripped
• Helps prevent overheating damage to internal components
• Restores normal operation when replaced

• Disconnect power to the appliance before service
• Note wire positions and terminal orientation before removal
• Use proper tools and avoid bending or stressing terminals
• After installation, check for underlying overheating causes (blocked airflow, failed fan, etc.)

The Knob is an OEM part for Frigidaire ranges. This component allows users to control the heat levels of the burners or the oven by turning the corresponding control shaft. It ensures precise adjustments for cooking and baking.

Over time, the knob can wear out or break due to frequent use, exposure to heat, or accidental impacts. Causes of a bad knob include cracking, stripping of the internal connection, or the knob becoming loose and difficult to turn.

Symptoms of a bad knob include:

• Difficulty in turning the knob
• Inconsistent or unresponsive heat adjustments
• The knob becoming loose or falling off
• Visible cracks or damage to the knob

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Seals the blower housing to prevent air leaks and maintain efficient airflow. Replace if torn, damaged, or causing reduced drying performance.

Secures the clock/timer or electronic oven control behind your range's control panel. Replace if bracket is bent, broken, or missing to keep display aligned.

This is a black cast iron burner grate that sits on top of a gas range cooktop, providing a stable surface to hold pots and pans over the burner flame. It supports cookware and distributes heat evenly during cooking. Replace this grate if it is cracked, warped, chipped, or if its rubber feet are missing, causing cookware to sit unevenly on the cooktop.

This is the rear blower housing that encloses and supports the blower fan assembly in a combination washer/dryer unit. It directs airflow through the dryer section to ensure proper drying performance. Replace this housing if it is cracked, warped, or damaged, which can lead to poor drying, unusual noises, or restricted airflow during the dry cycle.