Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer won't start or humming when you press start? The door switch signals when the door is closed. Easy 15-minute DIY repair with basic tools.
I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more
If your dryer runs but clothes stay wet or drying takes too long, the heating element may have failed. This coil heats air to dry clothes efficiently.
Ordered a new heating element. Read more
Refrigerator not cooling or freezer warm? The compressor assembly circulates refrigerant to maintain temperature. Professional installation recommended.
Ordered a new compressor and repaired by 3rd party. Read more
Dryer shuts off too soon or won't heat? A faulty high limit thermostat often causes premature shutoff. Simple DIY fix—usually takes 15 minutes or less.
Changed out high limit thernasstat Read more
Replace your dryer's control knob when cracked, broken, or missing. Attaches to the front panel for setting temperature, timing, and drying modes.
I would remove the knobs from the other switches to replace the timer one when it would break until all the knobs were broken. My wife kept blaming me for being a brute but i swear i was gentle when turning the knob. i ordered all new ones and guess what...the new knobs are reinforced with a metal ring to keep the plastic from splitting. guess it wasn't shear brute strength after all and just a inferior part.. Read more
Dryer door won't stay closed? A worn or broken door strike prevents proper latching. Easy 5-minute DIY fix with basic tools. Video guide included.
Replaced door strike and door latch Read more
Fix a dryer that won't heat or takes forever to dry clothes. This heating element assembly restores proper drying. Video guide included.
Found a video on UTube on how to dissamble the dryer. It was striaght forward and helpful. In the process I found an unusal amount of lint in the pipe from the dryer to the vent pipe to the outside It was nearly blocked about 10" up the pipe.. Read more
Dryer door won't stay closed? This door latch secures the door and activates the safety switch. Easy snap-in repair, typically 5-15 minutes.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
The bearing retainer secures the drum bearing assembly in your dryer. Replace if cracked, broken, or worn to restore proper structural support.
A few months back I changed out the "Bearing Slides" on the front side of the drum thinking that would stop the annoying squeaking every time we use the dryer. They were very worn and one was missing. But to my dismay it only lessened it by about 10%. After doing a bit more research I discovered the "Rear Shaft Bracket Assembly" also needed replacement. The tip was worn way down and clearly the source of the noise. It was actually a very simple repair except for the fact that the key to the... Read more
Fix a dryer that won't start, stops mid-cycle, or won't shut off with a new timer. Controls drying cycles and timing. 15-30 minute DIY repair.
Ordered both parts and got them in 2 days, removed 3 screws on back panel of dryer and removed defective timer , installed wires on new timer and put back in place and installed new knob , very easy repair only took 10 minutes and dryer was back up and running Read more
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also. Read more
Supports smooth dryer drum rotation and reduces friction. Replace if drum squeaks, wobbles, or rotates unevenly. Verify fit with your model number.
Watched a video online Read more
Replace your dryer's push to start button if cracked, broken, or worn. This button installs on the control panel. Commonly needs replacement due to wear.
Replaced the knob and it works perfect now Read more
Dryer won't start or keeps tripping the breaker? A damaged terminal block disrupts power distribution. DIY repair typically takes 30-45 minutes.
Had to replace power cord and entire terminal assy. Read more
Dryer won't heat, overheats, or shuts off mid-cycle? A faulty cycling thermostat often causes these issues. Easy DIY fix with our video guide.
Tested the old t-stat with ohm meter. When shaken, the contacts would open. Replaced it with new t-stat and it works fine now. Thanks! Read more
Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.
Removed 3 screws which required a torx bit. Used small headless nails to line up the holes and use as a guide for sliding on new diffuser. Put screws in one at a time and tightened down. rotating the drum helped with slight mis-alignement with the screw holes. Read more