Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replace your dryer's push to start button if cracked, broken, or worn. This button installs on the control panel. Commonly needs replacement due to wear.
Replaced the knob and it works perfect now Read more
Dryer won't start or keeps tripping the breaker? A damaged terminal block disrupts power distribution. DIY repair typically takes 30-45 minutes.
Had to replace power cord and entire terminal assy. Read more
The Thermistor is an OEM replacement part for GE dryers. This temperature-sensing device monitors air exhaust temperatures and communicates real-time readings to the control board. Precise thermistor functioning ensures the heating elements and drum engage safely and appropriately.
Symptoms of a faulty thermistor include:
Causes often relate to moisture exposure from normal operation degrading electronic performance over time. Physical stress or impact could potentially damage thin connecting wires.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryers.
Checked vent first to see if there was a blockage. Removed top, front and drum of dryer. Replaced all sensors including flame detection and gas valve coils. Re-assembled and tested. Dryer was now heating Read more
Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.
Removed 3 screws which required a torx bit. Used small headless nails to line up the holes and use as a guide for sliding on new diffuser. Put screws in one at a time and tightened down. rotating the drum helped with slight mis-alignement with the screw holes. Read more
Dryer won't start, stops mid-cycle, or runs backward? The drive motor powers drum rotation. Moderate difficulty repair requires disassembly. Video guide.
I could hear the dryer motor hum, but it would not run. There was nothing obstructing the motor from turning freely so I assumed I needed a new motor. I went ahead and ordered a new pulley switch to change out while I was in there just in case. The parts arrived faster than expected. I changed the switch first and then checked the old motor which surprisingly fired right up. Now I have to decide whether to return the new motor or keep it as a spare. Read more
Replaces a broken, cracked, or damaged lint trap duct assembly in your dryer. Directs airflow from the drum to the exhaust vent and houses the lint trap.
Our GE front loader dryer is approximately 10 years old. It started making a loud noise. Before we sank another $600 for a new dryer, I decided to go online to search Youtube videos to try to find out if anyone else had the same problem. I found that a lot of dryers had drum support bearings that wore out and needed to be replaced and a lot of dryers were also having clothes caught up in them. I then found an Appliance Parts Pro video on how to fix this problem and found out what parts... Read more
This replacement part is a high-limit thermostat, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This high-limit thermostat is typically found in dryers and controls the heat inside the drying tub. This is especially important as different dryer settings require different amounts of heat. If the high limit thermostat works properly, the temperature inside the tub should reach the correct amount during each drying cycle with no issues. A new high-limit thermostat might be needed if the user notices that the dryer is unable to reach the appropriate level of heat for a certain drying cycle. This is also true if the dryer is becoming too hot when the heat is supposed to be set to low. Make sure the dryer is cooled down prior to replacing this part as the areas in the back of the dryer can become very hot during use. Be sure to reference the specific user manual for more instructions on how to replace the thermostat. This thermostat is sold individually and is a genuine OEM part. The thermostat is sourced directly from the manufacturer.
Replaced thermal stats Read more
If your dryer won't heat or takes too long to dry, a faulty gas igniter is often the cause. This assembly heats up to ignite the burner for proper drying.
Installed a new igniter. Read more
Hi-limit thermostat. L210.
Great place to buy parts I can't say more than that Read more
Fix a dryer that won't heat with this outlet backup thermostat. Mounts on exhaust duct for over-temperature protection. DIY repair in under 1 hour.
Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.
Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.
I ordered two new baffles and 7 screws. I also ordered 6 large washers. We were running with one baffle held by only 2 of 3 screws. It appears that a repairman in the past had removed the large washers and over time, the screw heads reamed out the hole, causing the baffles to detach and break. In about 15 minutes, I was able to tighten up the existing baffle and add the two new ones. I also added the 6 big washers to help strengthen this to prevent future issues. I no longer have to listen to... Read more
Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.
This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.
Bonds dryer cabinet to ground point for safe operation. Replace if damaged, broken, or missing to restore proper electrical grounding and reduce shock risk.
Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.
After replacing the belt less than a year ago, when it broke again we started to think something may be going on with the idler pulley. Ordered a new belt and pulley wheel, only to have the belt break again the very next day. After a call to customer service explaining the situation, they replaced the belt and pulley wheel which were both under warranty, and suggested replacing the arm itself. We also had to replace the interlock switch. Parts arrived quickly. The repair itself took about an... Read more