Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
If your dryer runs but clothes stay wet or drying takes too long, the heating element may have failed. This coil heats air to dry clothes efficiently.
Ordered a new heating element. Read more
Supports the front of the dryer drum as it rotates, reducing friction and noise. Replace if you hear squeaking or grinding sounds during operation.
With your ordering page. Getting the right parts was super easy, fast. From ordering, shipping, and installing new parts. It was just three days Shipping was fast and reasonable. Thank you Read more
Dryer door pops open during cycle or won't stay closed? Replace the door latch. This part secures the door to the cabinet. Easy 5-minute DIY fix.
We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more
Dryer won't shut off or gets too hot? The cycling thermostat regulates temperature during the cycle. DIY repair with video guide, typically 1 hour.
Did continuity tests on the sensors, till I figured out what one was bad. Read more
Idler pulley for dryer drum assembly. Maintains belt tension to enable smooth drum rotation. Replace if worn, cracked, or causing noise during operation.
The Dryer is 10 years old GE Front Load DPVH890JEMG. The drum would intermittently not rotate at the beginning of a cycle and occasionally would rotate but then start and stop throughout the cycle. I did not check error codes, but the windings on the motor were black. So it seemed reasonable that the motor was overheating and sending a signal to the control board to stop. There is one screw under the knob and 9 screws on the front to get inside. I decided to replace the bearings, capacitor,... Read more
Dryer shuts off too soon or won't heat? A faulty high limit thermostat often causes premature shutoff. Simple DIY fix—usually takes 15 minutes or less.
Changed out high limit thernasstat Read more
The O Ring is an OEM part for GE dryers, creating a tight seal in different components for efficient operation. This small part prevents air leaks that can impact drying performance, made from quality materials to withstand high temperatures and frequent use
Causes of a faulty O Ring in a dryer may stem from heat exposure, regular wear and tear, or chemical damage. This can result in reduced elasticity, cracks, or breaks, impacting the seal.
Symptoms of a bad O Ring in your dryer include:
This genuine GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Went ahead and replaced the pulley as well the drum bearing sleeve and O ring, drum belt and the front drum bearing slides. Put the unit back together and she ran like a top! Read more
Dryer not heating or taking too long to dry? This heating element and housing assembly restores heat production. DIY-friendly repair for electric dryers.
Replaced heating element. Read more
Replacement start button for dryer control panel. Installs on front console. Needed when original button is cracked, broken, or won't depress properly.
The start button broke?!? I ordered another start button and it looked exactly like the one I had. I figured it would break as well, so I might as well try to fix the broken one. I unplugged the power, removed the back of the dryer console, disconnected the start switch from the button and the dryer, depressed the 3 pop out tabs to remove the button from the dryer. I put the switch back in place and reinstalled the back. I clipped off the 3 projections that kept the button from being... Read more
Replaces broken, cracked, or sagging dryer door hinges. Mounts to the door frame for smooth opening and closing. Sold individually, screws not included.
Replaced hinges Read more
The bearing retainer secures the drum bearing assembly in your dryer. Replace if cracked, broken, or worn to restore proper structural support.
A few months back I changed out the "Bearing Slides" on the front side of the drum thinking that would stop the annoying squeaking every time we use the dryer. They were very worn and one was missing. But to my dismay it only lessened it by about 10%. After doing a bit more research I discovered the "Rear Shaft Bracket Assembly" also needed replacement. The tip was worn way down and clearly the source of the noise. It was actually a very simple repair except for the fact that the key to the... Read more
Dryer won't heat or won't turn on? A failed high limit thermostat often causes these issues. This safety part prevents overheating. DIY-friendly repair.
Found open thermal fuse. While it was apart, cleaned out all the lent and lubed drum bearing. Read more
Plastic baffle that installs inside the dryer drum to lift and tumble clothes. Replace if cracked, broken, thinning, or missing vanes that may mark fabrics.
Replaced front drum support, both sets of dryer bearing slides and flipped felt pcs in front drum support. Repair video was very helpful Read more
Complete dryer door assembly with frame, glass, and handle. Replace if your door is cracked, dented, scratched, or has broken hinges or latch components.
Replaced the door assembly. Read more
If your dryer won't start or the door won't latch securely, the door strike may be worn or broken. This part ensures proper door closure. Easy DIY fix.
The repair went as planned Read more
Dryer won't start or run? A blown thermal fuse is often the cause. This safety part cuts power when overheating occurs. DIY-friendly repair.
The part I ordered fixed my problem Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.