Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Dual Coil Water Valve is an OEM replacement part for GE washing machines. It is a solenoid valve that controls the flow of hot and cold water to the washer.
Symptoms of a faulty valve include:
Causes can be worn seals or mineral buildup impeding proper valve movement after extended use.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Replaced the water fill water valve. Read more
The Timer is an OEM part for GE electric dryers. It serves as the critical control module that monitors and regulates dryer cycle times during functions like regular, wrinkle guard, fluff and more. Causes of a bad timer include failure of internal electronic components or wiring connections due to prolonged exposure to heat and vibration inside the dryer cylinder. Mechanical wear of buttons or dials used to program cycles may occur as well over time. Symptoms of a bad Timer include:
The GE OEM part is also compatible with Hotpoint, RCA and select Kenmore models.
Replaced the timer switch and knob. Read more
Fix a washer that won't drain or leaves standing water. This drain pump removes water from the drum during drain and spin cycles. Moderate DIY repair.
Bought a new drain pump works fine now. Read more
Seals the gap between outer tub and wash basket to prevent leaks. Replace if water leaks from bottom during wash cycles. Confirm fit by model number.
I will say that the GE Washer/Dryer combo is nice if you need to save space, but trying to fix it was far from "fun". It took several hours to get to the location of the Seal Tub. First the dryer had to come off the top, then pretty much every bit of the internals needed to come out too, The seal could not be accessed from the bottom of the machine, and it wasn't easy to get to it from the top. If you have patience, and keep track of everything you did, so you can undo it, the project can be... Read more
This drive belt transfers motor power to your washer dryer combo's pulley system. Replace when you notice squealing, slipping, or burning odors.
Replaced transmission and support assembly. Hub nut corrode on support, spanner wrench would not loosen. Had to use 1 11/16 deep socket and impact wrench to remove, basket would not com off support even after cleaning out and soaking with penetrant and using automotive air hammer to push out. I had to cut support plate in half with die grinder, cut bearing from shaft and punch out agitator shaft then use die grinder with carbide burr to cut basket shaft in two before basket would come off... Read more
The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying. Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions. Symptoms of a bad flame sensor include:
GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes. Also, the old solenoids tested... Read more
Captures lint and debris from dryer exhaust to prevent vent clogs and fire hazards. Replace if damaged, cracked, or no longer sealing properly.
I just placed the slide in the slots and slid it to the locked position. I had to bend the top left slide lock on the door to get it to lock properly. Read more
This shifter spring helps engage and return the transmission shifter mechanism in select top-load washers, allowing smooth changes between agitation and spin for reliable wash performance.
It was super easy- Pop off the top where the fabric softener goes- undid bolt pop out the agitator ( the hardest part getting this out and the new one in). Got the new one lined up push in place use a rubber mallet to secure put in bolt and good to go May I say this company is excellent- great customer service and delivers as said 5 stars all the way. Read more
Secures the inner tub to the drive shaft in top-load washers. Replace if corroded, stripped, or damaged during tub seal or transmission repairs.
Washer won't start or spin? This lid lock magnet triggers the safety sensor to confirm the lid is closed. Simple DIY fix restores normal operation.
Dryer won't heat, overheats, or shuts off mid-cycle? A faulty cycling thermostat often causes these issues. Easy DIY fix with our video guide.
Tested the old t-stat with ohm meter. When shaken, the contacts would open. Replaced it with new t-stat and it works fine now. Thanks! Read more
Dryer won't start, stops mid-cycle, or runs backward? The drive motor powers drum rotation. Moderate difficulty repair requires disassembly. Video guide.
I could hear the dryer motor hum, but it would not run. There was nothing obstructing the motor from turning freely so I assumed I needed a new motor. I went ahead and ordered a new pulley switch to change out while I was in there just in case. The parts arrived faster than expected. I changed the switch first and then checked the old motor which surprisingly fired right up. Now I have to decide whether to return the new motor or keep it as a spare. Read more
This lid actuator engages the washer's lid switch or lock when the lid closes, signaling the control that it's safe to run. Replacing a worn or broken actuator restores reliable lid detection for wash and spin cycles.
Installed the new Lid Actuator and the dryers Start Switch. Read more
The Kit Sensor Speed is an OEM part for GE washing machines. It plays a crucial role in monitoring the drum's speed and movement, ensuring that the washer operates with optimal efficiency and precision. This sensor helps adjust the spin cycle based on the load, which is essential for proper balancing and to prevent excessive vibration and noise.
Symptoms of a failing Kit Sensor Speed include:
Causes of a bad sensor can stem from electrical faults like wiring issues or component malfunctions, physical damage from overload or impacts, or simply wear and tear over time.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This replacement part is a high-limit thermostat, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This high-limit thermostat is typically found in dryers and controls the heat inside the drying tub. This is especially important as different dryer settings require different amounts of heat. If the high limit thermostat works properly, the temperature inside the tub should reach the correct amount during each drying cycle with no issues. A new high-limit thermostat might be needed if the user notices that the dryer is unable to reach the appropriate level of heat for a certain drying cycle. This is also true if the dryer is becoming too hot when the heat is supposed to be set to low. Make sure the dryer is cooled down prior to replacing this part as the areas in the back of the dryer can become very hot during use. Be sure to reference the specific user manual for more instructions on how to replace the thermostat. This thermostat is sold individually and is a genuine OEM part. The thermostat is sourced directly from the manufacturer.
Replaced thermal stats Read more
Drain hose assembly routes wastewater from the washer pump to your standpipe or laundry tub. Replace if cracked, kinked, leaking, or causing floor puddles.
First of you need to remove front panel of the washer, using a putty knife push the tabs between the top of the machine and the front panel. Once front panel is exposed drain hose is connected to pump which is in the front of the machine,very easy to access with the front off. Remove old hose with pliers and discard ,run new hose thru outlet on the back of the machine and secure new hose to drain and secure hose to the machine, reinstall front panel of washer and that's it Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.