Gtw460asj5wwn Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

Noticed that lid lock light was not on, googled problem, ordered parts, working on 3rd day. Read more

I opened the cover panel of the control board. I visually checked for burns on the board and verified all connectors were firmly seated. I opened the bottom of the unit, and I saw the service manual in a zip-lock bag. From this manual, I verified that the drain pump resistance is good, the start capacitor is good, and the lid switch is good. I entered diagnostic service mode. Persistent alarms are 4 and 25.Error 4 means Reset Monitor, while Error 25 means Pressure Sensor Dropout. I... Read more

Replace belt. Read more

Replaced all 4 rod and spring assemblies. Read more

I looked at videos and read several blogs about my GE GTW460ASJ6WW washer not agitating. They all pointed to changing the Clutch and Washer mode shifter. Pretty easy repair that only took about 15 minutes. The old parts looked ok but changed them anyway. This DID NOT solve the problem. Took a closer examination of the agitator. I could turn the Agitator Base by hand without the drum turning. AHAH, maybe the screw came out? So I tried to get the Auger off to access the 7/16” bolt holding... Read more

Replaced all 4 rod and spring assemblies. Read more

GE Washer m/n GTW460ASJ6WW would allow other fill levels, but when set to "super" it would never stop filling. Checked water inlet valve (by initiating a fill and unplugging the unit) to see if the inlet valve was sticking open, that was not the issue. Decided to replace the board even though it is a significant fraction of the cost of a new washer. Local appliance stores didn't have the board but APP did, and of course, they are open 24/7 while my local part stores have decided the weekend is... Read more

I looked at videos and read several blogs about my GE GTW460ASJ6WW washer not agitating. They all pointed to changing the Clutch and Washer mode shifter. Pretty easy repair that only took about 15 minutes. The old parts looked ok but changed them anyway. This DID NOT solve the problem. Took a closer examination of the agitator. I could turn the Agitator Base by hand without the drum turning. AHAH, maybe the screw came out? So I tried to get the Auger off to access the 7/16” bolt holding... Read more

After a few internet searches, it became clear that the most common fix for this issue is replacing the water inlet valve. My washer is about five years old, which aligns with the typical lifespan of these valves. I ordered the OEM parts for this washer, as this is not something you want failing and potentially flooding your home while you’re away. The thermistor is installed directly into the valve and uses an O-ring that is known to degrade and leak over time. Since the thermistor has to be... Read more

Replaced the belt. Read more

Ordered a new timer and knob. The husband was able to fix in about 20 minutes and now works like new. Read more

I purchased gear box WH03X33729 from AppliancePartsPros.com and installed it following the video below submitted by Teknisimu on YouTube, Taking my time the repair took about 2 hours from start to finish. I received my parts in one day using FedEx next day, well worth the cost! https://www.youtube.com/watch?v=yBUHpc7nKaE I can't forget the help I received from Jake on Appliance Blog.com, Thank you Jake! Read more

I ordered the parts, after assuring my diagnosis was correct from APP’s knowledgeable representative, and they were shipped quickly. I tipped the washer and disassembled the parts to be replaced and then installed a new clutch, clutch spring and mode shifter. Read more

I found a YouTube video, order the parts about midnight Saturday and-they came in the mail before lunch on Tuesday. I laid the washer on the rear panel, removed both pulleys to clean them, installed the speed sensor. bolted the pulleys back in place, installed the new belt-making sure it was centered and everything moved freely, and attached the belt/pulleys cover. I set the washer back up, reattached the water lines, placed the drain tube, and plugged in back in. Works like new !!! 30 minutes... Read more

Replaced thr motor pulley and transmission pulliey and belt. Read more