Gtwwn2800d1ww Parts

This Bottom Hinge Pin supports the refrigerator door at the lower hinge, providing a smooth, stable pivot. Replace a worn or bent pin to restore proper door alignment, closing action, and gasket sealing.

• Serves as the pivot point for the door on the bottom hinge bracket
• Helps maintain alignment so the door gasket seals correctly
• Wear/failure symptoms can include door sagging, wobble at the hinge, squeaks or grinding, and poor self-closing
• Replacing a damaged pin can reduce hinge play and improve door operation

• Disconnect power; turn off water supply if working near a dispenser line
• Remove items from the door and support the door to prevent strain on hinges
• Detach bottom hinge fasteners, lift door off, replace the pin, and reassemble
• Adjust hinges as needed

Size: 10-12 a. Includes 12 screws.

The Cabinet Roller is an OEM part for Whirlpool refrigerators. It facilitates the smooth movement and positioning of the refrigerator cabinet, making it easier to adjust or relocate the appliance as needed. This roller is designed to support the weight of the refrigerator while allowing for effortless mobility.

Causes of a bad Cabinet Roller can include wear and tear over time, exposure to heavy loads, or damage due to rough handling or impact. These factors can lead to the roller becoming ineffective or breaking altogether, resulting in difficulty moving the refrigerator.

Symptoms of a bad Cabinet Roller include:

• Difficulty moving or adjusting the refrigerator
• Unusual noises when attempting to move the appliance
• The refrigerator not sitting level or wobbling

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

The Platform Bearing Retainer & Fasteners is an OEM part for GE washers. It serves as a backing plate that secures the suspension assembly bearing in place on the washing machine tub. The retainer helps manage stress and distribute weight evenly across the bearing. 

Causes of a bad retainer and fasteners include worn threads, stripped holes, or loose mounting from repeated vibration and load shifting during the spin cycle.

Symptoms of a bad Platform Bearing Retainer and fasteners include:

• Excessive vibration or shaking of the washing machine tub 
• Noise or grinding sounds from the suspension assembly
• The tub not sitting level or wobbling during the operation
• Leaks caused by stress on the tub seal

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Size: 10-32 GXTT FLP.595 S

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

The tub cover assembly seals the top of the washer's outer tub to contain splashes and keep the basket clear. Replacing a damaged cover helps stop leaks from the top area and restores clean, consistent wash performance.

• Seals the outer tub opening to prevent water from escaping during fill and agitation
• Helps direct water back into the tub and reduces splashing
• Maintains proper basket clearance to avoid rubbing or scraping
• Common signs it's failing: water leaking or splashing from the top/sides, visible cracks or broken tabs, loose or misaligned cover, rubbing noises

• Disconnect power and water supplies before servicing; wear gloves to protect hands
• Lift/remove the top or lid as needed to access the tub opening
• Release the retaining fasteners/clamps and carefully lift off the old cover; note orientation
• Seat the new cover evenly, align all tabs, reinstall fasteners, and test for leaks and basket clearance

Original OEM Phillips wafer head screw 8 - 18 X 3/8 inch

Replace a failed speed sensor to restore accurate motor feedback for your washer. This sensor monitors drive speed so the control can regulate agitation and spin; when it fails, cycles can stall, stop, or skip spin. What it does:

• Monitors drive motor/basket speed and sends feedback to the control
• Enables precise regulation of agitation and spin speeds
• Failure can cause no-spin or no-agitate conditions and erratic cycle behavior
• May trigger fault codes related to speed sensing/tachometer feedback

• One speed sensor

• Disconnect power and turn off water before servicing
• Access the drive motor area (location varies by model); note connector orientation
• Transfer any mounting clip/screw if present; seat the sensor fully and secure wiring away from moving parts
• After installation, run a spin or service test to ensure proper operation

This grommet is a small protective seal used where a hose, tube, wire, or component passes through or mounts to the appliance cabinet. It cushions the connection and helps prevent leaks, vibration, and wear for reliable operation.

• Provides a snug barrier between parts and metal openings to protect hoses, tubes, and wiring
• Helps seal against moisture to reduce seepage
• Dampens vibration and rattling noises
• Replace if cracked, hardened, missing, or no longer stays seated; symptoms may include drips at a pass-through, buzzing/rattling, or a loose fit

• Disconnect power; shut off water supply if applicable
• Access the grommet location and note orientation/routing
• Remove the old grommet and clean the opening
• Press the new grommet fully into place; reassemble and test for leaks/noise

This pressure switch senses the washer's tub water level and signals the control to stop filling and advance the cycle. Replacing a faulty switch restores proper fill levels and helps resolve overfilling, no-fill, and cycle-advance issues.

• Monitors water level via air pressure through the tub's pressure hose
• Signals the control to shut the inlet valves and begin wash/agitate or spin
• Helps advance the cycle once the target water level is reached
• Common failure symptoms include continuous filling/overfill, no fill or low fill, won't agitate/spin, or stopping mid-cycle with water-level errors

• Unplug the washer before servicing; turn off water supply
• Access the switch in the control console/top panel; move wire connectors to the new switch one at a time
• Inspect the pressure hose for kinks, cracks, or water in the line and seat it firmly on the new switch
• Run a test fill to ensure the water shuts off at the selected level

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This double-style hinge bushing supports the washer lid hinge pin and provides a smooth bearing surface. Replacing a worn bushing restores quiet, even lid movement and helps keep the lid properly aligned over time.

• Supports and centers the lid at the hinge
• Provides a low-friction bearing surface for the hinge pin/rod
• Helps reduce squeaking, looseness, and metal-on-metal wear
• Can help resolve a wobbly, misaligned, or scraping lid

• Disconnect power before servicing; support the lid to prevent dropping
• Remove the hinge pin/rod or screws as your model requires to access the bushing
• Pry out the worn bushing and press the new bushing fully into the hinge opening
• Reassemble and check lid operation; consider replacing the opposite-side bushing if worn

This PTC start relay mounts on the compressor and briefly powers its start winding to get it running, then drops out. Replacing a weak relay can restore reliable starts and resolve clicking/humming with no cooling.

• Provides the initial boost to the compressor via a positive temperature coefficient (PTC) element, then opens as it heats
• Takes the start winding out of the circuit once the compressor is running
• Typical failure symptoms: compressor won't start, repeated clicking/humming, no cooling, visible heat damage at the relay or connector
• Direct replacement for the original PTC start device used on applicable models

• Disconnect power before servicing; allow hot components to cool
• Access the compressor compartment, remove the cover, and note the relay's orientation; pull the old relay straight off the compressor pins
• Inspect wiring terminals for heat damage; do not reuse burnt connectors
• Firmly seat the new relay on the compressor terminals, reinstall the cover, restore power, and verify compressor start