Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Drive belt connects the motor to the drum in your laundry center. Replace if you notice burning smell, smoke, or the drum won't spin. Verify fit by model.
Replaced motor. Read more
The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance.
Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching.
Symptoms of a bad Door Latch include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
Seals the gap between outer tub and wash basket to prevent leaks. Replace if water leaks from bottom during wash cycles. Confirm fit by model number.
I will say that the GE Washer/Dryer combo is nice if you need to save space, but trying to fix it was far from "fun". It took several hours to get to the location of the Seal Tub. First the dryer had to come off the top, then pretty much every bit of the internals needed to come out too, The seal could not be accessed from the bottom of the machine, and it wasn't easy to get to it from the top. If you have patience, and keep track of everything you did, so you can undo it, the project can be... Read more
The Dual Coil Water Valve is an OEM replacement part for GE washing machines. It is a solenoid valve that controls the flow of hot and cold water to the washer.
Symptoms of a faulty valve include:
Causes can be worn seals or mineral buildup impeding proper valve movement after extended use.
Replaced the water fill water valve. Read more
The Timer is an OEM part for GE electric dryers. It serves as the critical control module that monitors and regulates dryer cycle times during functions like regular, wrinkle guard, fluff and more. Causes of a bad timer include failure of internal electronic components or wiring connections due to prolonged exposure to heat and vibration inside the dryer cylinder. Mechanical wear of buttons or dials used to program cycles may occur as well over time. Symptoms of a bad Timer include:
The GE OEM part is also compatible with Hotpoint, RCA and select Kenmore models.
Replaced the timer switch and knob. Read more
The Board & Support Assembly is an OEM replacement part for GE washer/dryer combination laundry centers. This assembly features both the control board and its supporting structure. The control board is responsible for managing a variety of functions for both the washing machine and dryer, including cycle selection and timing, while the support secures the board in its proper position. Causes for a malfunctioning Board & Support Assembly can include electrical issues like short circuits or power surges, as well as physical damage from impact or mishandling. Symptoms of a bad Board & Support Assembly include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
After a power surge due to a panel miss-wire, I burned up the board on a washer/dryer combo. I had an electrician fix the panel and ordered a new board from Appliance Parts Pros. Installation took about 30 minutes and after that, everything worked fine. Read more
This drive belt transfers motor power to your washer dryer combo's pulley system. Replace when you notice squealing, slipping, or burning odors.
Replaced transmission and support assembly. Hub nut corrode on support, spanner wrench would not loosen. Had to use 1 11/16 deep socket and impact wrench to remove, basket would not com off support even after cleaning out and soaking with penetrant and using automotive air hammer to push out. I had to cut support plate in half with die grinder, cut bearing from shaft and punch out agitator shaft then use die grinder with carbide burr to cut basket shaft in two before basket would come off... Read more
Secures the inner tub to the drive shaft in top-load washers. Replace if corroded, stripped, or damaged during tub seal or transmission repairs.
Captures lint and debris from dryer exhaust to prevent vent clogs and fire hazards. Replace if damaged, cracked, or no longer sealing properly.
I just placed the slide in the slots and slid it to the locked position. I had to bend the top left slide lock on the door to get it to lock properly. Read more
The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying. Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions. Symptoms of a bad flame sensor include:
GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes. Also, the old solenoids tested... Read more
Dryer won't start or keeps tripping the breaker? A damaged terminal block disrupts power distribution. DIY repair typically takes 30-45 minutes.
Had to replace power cord and entire terminal assy. Read more
Dryer won't heat, overheats, or shuts off mid-cycle? A faulty cycling thermostat often causes these issues. Easy DIY fix with our video guide.
Replaced cycling thermostat. Read more
Control board failed and washer or dryer won't start? This UI board assembly manages all washing and drying functions in your laundry center unit.
I put the part on. It matched correctly. The washing machine is working better than ever! Read more
The Kit Sensor Speed is an OEM part for GE washing machines. It plays a crucial role in monitoring the drum's speed and movement, ensuring that the washer operates with optimal efficiency and precision. This sensor helps adjust the spin cycle based on the load, which is essential for proper balancing and to prevent excessive vibration and noise.
Symptoms of a failing Kit Sensor Speed include:
Causes of a bad sensor can stem from electrical faults like wiring issues or component malfunctions, physical damage from overload or impacts, or simply wear and tear over time.
This shifter spring helps engage and return the transmission shifter mechanism in select top-load washers, allowing smooth changes between agitation and spin for reliable wash performance.
Washer won't start or spin? This lid lock magnet triggers the safety sensor to confirm the lid is closed. Simple DIY fix restores normal operation.