Hss251fmcww Parts

The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more

First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more

Replaced Ice maker very easy. Read more

Replaced the worn parts. Read more

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

Went to appliance parts Web site looked at the symptoms ordered the suggested parts, my favorite was watching the part repair video, on what the part does and how to install, got the parts the next day, defrosted the fridge 100%, and one by one installed each part what an easy process the video showed exactly where the part was located and how to remove the old and install the new one, now my fridge is working and cooling better than before I saved over $1,400, didn't have to buy a new... Read more

I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more

Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more

I ordered the recommended front door shelf part Fz for my frig, it was shipped promptly. It was slightly too long, so I cut about a 1/4" with the saw... it fits nicely now. Read more

Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more

Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more

Replaced trim. Read more

I was able to take it all apart and order the new parts. Disassembly took about 45 minutes and assembly took about 30 minutes. Read more

I removed the drawers and old rails, and screwed in the new ones. It was very straightforward. Read more

Replaced motor and solenoid cube along with dispenser auger. Simply watched video on repair and installation and really had no problem. My refrigerator is so old that one of the holes in the motor did not align properly. Had to drill another hole to mount the motor to the housing, took ten minutes. The ice auger took the longest as I was afraid of breaking the plastic housing trying to get the tabs to release. Had to watch the video twice to make sure I got the blades back in the right order.... Read more