Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also. Read more
Dryer won't start or run? A blown thermal fuse is often the cause. This safety part cuts power when overheating occurs. DIY-friendly repair.
The part I ordered fixed my problem Read more
Dryer won't start or keeps tripping the breaker? A damaged terminal block disrupts power distribution. DIY repair typically takes 30-45 minutes.
Had to replace power cord and entire terminal assy. Read more
Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.
Removed 3 screws which required a torx bit. Used small headless nails to line up the holes and use as a guide for sliding on new diffuser. Put screws in one at a time and tightened down. rotating the drum helped with slight mis-alignement with the screw holes. Read more
Replace your dryer's push to start button if cracked, broken, or worn. This button installs on the control panel. Commonly needs replacement due to wear.
Replaced the knob and it works perfect now Read more
Dryer door won't stay closed or pops open during cycle? This mounting plate anchors the door strike for secure latching. Quick DIY fix with video guide.
We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more
Hi-limit thermostat. L210.
Great place to buy parts I can't say more than that Read more
Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.
Replaced the top bearing assembly, drive belt, and blower wheel. The most time consuming and difficult part was putting the new drive belt back on the pulley and tensioner. Be sure to know how it is routed through them. It is a very tight fit getting your arm in there and connecting it blindly. Read more
Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.
I ordered two new baffles and 7 screws. I also ordered 6 large washers. We were running with one baffle held by only 2 of 3 screws. It appears that a repairman in the past had removed the large washers and over time, the screw heads reamed out the hole, causing the baffles to detach and break. In about 15 minutes, I was able to tighten up the existing baffle and add the two new ones. I also added the 6 big washers to help strengthen this to prevent future issues. I no longer have to listen to... Read more
This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.
First I check the breaker for the dryer then I check the power cord and the ohms to the power cord when all this things were in working order I then check the ohms to the fuse to the control panel. The fuse had no ohms so I got a pair on needle nose pliers pulled out the fuse and replace it worked just find after that Read more
Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.
This fuse terminal cover shields and insulates the fuse connection inside your appliance, helping prevent accidental contact and shorting. Replace a cracked or missing cover to maintain safe electrical protection and dependable circuit performance.
This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.
Replaced the screw Read more
Bonds dryer cabinet to ground point for safe operation. Replace if damaged, broken, or missing to restore proper electrical grounding and reduce shock risk.
This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.
Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.
After replacing the belt less than a year ago, when it broke again we started to think something may be going on with the idler pulley. Ordered a new belt and pulley wheel, only to have the belt break again the very next day. After a call to customer service explaining the situation, they replaced the belt and pulley wheel which were both under warranty, and suggested replacing the arm itself. We also had to replace the interlock switch. Parts arrived quickly. The repair itself took about an... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.