Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Used to lock washer cabinet to rear wall of washer.
Just took off the old vacuum break and put the new one on. It was very easy because the site had a video showing how and I watched it first. Read more
Washer won't stop spinning smoothly or makes loud jerking noise when stopping? The brake shoe stops the tub during spin cycles. DIY repair in 1-2 hours.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Loud rattling or loose agitator during wash? This clip secures the agitator assembly to eliminate noise and restore proper back-and-forth motion. Quick DIY fix.
Found that by manually spinning agitator one direction it seemed free, but spinning counterclockwise it seemed to stick a little. Pulled dispenser and agitator and found the agitator washer hole was oval rather than round. Replaced the agitator washer and the washer seems to sound normally for now. Not sure if the new agitator washer will eventually grind down due to non-circular action from the transmission, or if the agitator and clip will keep the transmission centered long term. Should... Read more
These lid bumpers are sold individually.
Found AppliancePartsPros on-line. Sent us the manual, parts list, etc. via .pdf files. Our local guy did not. Had parts in stock, two day shipping, totally painless. The parts were approximately 1/2 the price the local guy wanted. OEM parts. Perfect fit on replacement. The Whirlpool is so well made, it was very easy to repair. It has several items, over the years, which failed. In all cases, repair was painless with a few common hand tools and a tad of patience. AppliancePartsPros had... Read more
Agitator not moving clothes properly or spinning weakly? This straight-vane agitator restores wash action in 10 minutes with basic hand tools.
Replaced it Read more
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
Fix a washer that won't fill properly or overfills with this pressure switch. Controls water level sensing. DIY-friendly repair, about 5-10 minutes.
After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety. Then removed 4 screw out side panel and 2 screw in side to get lose. After all, replaced a new part and put all panel and screw back together. Finally, plug in electrical power then a water hose and test a new part just installed. So far so good, seem like everything was function OK. Again, thanks for your web... Read more
Washer motor shield deflects water, lint, and debris away from the drive motor. Replace if cracked or missing to prevent motor damage. Simple install.
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Replaced flow meter and control valve Read more
Fix a washer that fills but won't spin or agitate. This motor start capacitor stores electrical energy to help start your washer motor. DIY repair.
I was actually getting an error code for the shifter and speed sensor. I ordered a shifter, which included the speed sensor, and replaced that part but the washer still didn't work. After doing some more research online, someone mentioned that the capacitor may be bad. After talking to my dad, who is an electrician, he said it sounded like my problem could very well be the capacitor. Knowing that we'd been without a washer for almost two weeks at this point, I went ahead and ordered the... Read more
Structural bracket that secures the rear panel to the washer chassis. Replace if cracked, broken, or missing to restore proper alignment and cabinet stability.
In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more
Snaps onto the outer tub to contain splashing and guide water back into the basket. Replace if cracked or loose to stop leaks and prevent imbalance issues.
Replace the all four suspension and ring tub. it work like brand new. thanks for having the parts that i needed. and the fast shipping. michael moore Read more
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. Sold individually, four are needed to replace all parts. Screw part number WP3390631.
Cracked bleach dispenser leaking onto your washer? This cup holds and meters bleach during wash cycles. Simple snap-in installation, video included.
Found and ordered another one, worked out great. Good seller, quick shipper. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.