Jvm7195s1ss Parts

This hardware assembly secures designated components in your appliance, restoring a tight, rattle-free fit after service or wear. Replacing damaged or missing fasteners helps keep panels and parts aligned and operating as designed.

• Provides the correct fasteners/spacers for the specified location on the unit
• Replaces stripped, lost, or corroded hardware
• Helps eliminate looseness, vibration, or rattling noises
• Supports proper alignment and fit of the associated part or panel

• Disconnect power before servicing; allow hot surfaces to cool
• Support the part being fastened to prevent damage or misalignment
• Match each fastener one-for-one; note orientation and any washers/spacers
• Hand-start threads and do not overtighten; verify clearances and operation after install

The Fuse is an OEM part for GE microwaves. It serves as a safety device that protects the microwave by breaking the circuit if there is a power surge or electrical fault. This helps prevent damage to the microwave's components and ensures safe operation.

You should replace the fuse if it becomes blown or damaged. Causes of a bad fuse can include power surges, electrical faults, or issues within the microwave such as overheating. These factors can cause the fuse to blow, rendering the microwave inoperable.

Symptoms of a bad fuse include:

• The microwave not turning on or suddenly losing power
• No response from the microwave’s control panel
• The microwave stopping mid-cycle without completing the cooking process

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement light socket restores safe, consistent power to the appliance light. If the original socket is heat-damaged, loose, or shorted, installing a new socket brings back reliable illumination and solid electrical contact.

• Provides the electrical connection and physical support for the light bulb
• Replaces cracked, scorched, or worn sockets that cause poor contact
• Helps resolve a light that won't turn on, flickers, or works intermittently with a known-good bulb
• Designed for a secure fit to maintain dependable lighting performance

• Disconnect power at the breaker before servicing.
• Allow the area to cool before working near any heated light cavity.
• Transfer wires one at a time (or take a quick photo) to ensure correct reconnection.
• Install a bulb type and wattage specified for your model; avoid touching bulb glass with bare hands if your model uses a halogen lamp.

This mounting plate assembly is the rear wall bracket that supports and secures the microwave during installation. Replacing a bent or missing plate ensures a safe, level mount and stable operation without vibration or shifting.

• Acts as the rear-wall support the microwave hangs on and bolts to
• Maintains proper, level alignment of the unit and door
• Helps prevent vibration, rattling, or shifting during use
• Replace if the plate is bent, damaged, corroded, or missing

• Disconnect power and have a second person support the microwave before removal/installation
• Follow your model's installation template and manual for hole locations and hardware
• Fasten to wall studs or appropriate anchors; level the plate before tightening
• Verify clearances and door swing before fully tightening mounting hardware

This turntable coupler connects the microwave's turntable motor to the glass tray to drive smooth rotation during cooking. Replacing a worn coupler restores even heating and prevents the tray from slipping, stalling, or wobbling. What it does:

• Transfers rotation from the turntable motor to the glass tray
• Centers and supports the tray for stable, even spinning
• When worn or cracked, may cause the turntable not to turn, slip, wobble, or click/grind at the center hub
• Helps restore consistent heating by ensuring proper tray movement

• 1 turntable coupler

• Disconnect power by unplugging the microwave or switching off the breaker before service
• Remove the glass tray and roller ring; lift the old coupler straight up off the motor shaft
• Align the new coupler with the shaft and press firmly until fully seated

This hood damper assembly opens to allow exhaust airflow and closes to help block outside drafts and odors when the fan is off. It restores proper venting and prevents back-drafts in over-the-range hoods and microwaves. What it does:

• Opens with the vent fan to let cooking smoke and steam exit the home.
• Closes when the fan is off to reduce backdrafts, outside air, and odors.
• A faulty or stuck damper can cause reduced airflow, rattling noises, or air blowing back into the kitchen.
• Works as the moving flap between the appliance exhaust and the ductwork to control airflow direction.

• Disconnect power to the appliance (unplug or shut off the circuit breaker) before servicing.
• Access typically requires removing the hood or microwave grille/cover; keep track of screws and mounting hardware.
• Basic hand tools (screwdrivers, possibly a nut driver) are usually sufficient; handle the damper flap gently to avoid bending.
• After installation, restore power and run the fan to ensure the damper opens and closes smoothly.

This latch body is the door latch component that secures the appliance door during operation, restoring reliable closure so cycles can run normally. Use it to replace a worn or damaged latch that won't hold the door closed. What it does:

• Engages the door striker to hold the door closed and maintain a proper seal during operation
• Works with the door latch mechanism so the appliance can complete cycles that require a closed door
• Common symptom: door won't stay closed, is difficult to latch, or feels loose at the latch point
• Replacing a damaged latch body can prevent intermittent door-open errors and restore normal door operation

• Disconnect power (unplug or turn off circuit breaker) before starting any repair
• Remove the door or access panel as needed; keep track of fasteners and any trim pieces
• Handle door glass and trim carefully to avoid damage; test latch engagement before full reassembly

This 50-watt halogen lamp restores bright, reliable lighting in your appliance. Replace a burned-out bulb to see clearly while cooking and checking food progress, keeping the cavity or cooktop area illuminated as designed.

• Provides focused illumination for the interior cavity or cooktop/task lighting
• Restores light when the door opens or the light pad/switch is used
• Common symptoms: no light, dim or flickering light, or darkened/burned-out bulb
• Using the correct 50-watt halogen rating helps protect the socket and wiring

• Disconnect power (unplug or switch off the breaker) before replacing the lamp
• Allow the lamp and surrounding area to cool completely
• Do not touch the glass; handle with clean gloves or a tissue to avoid oil contamination

This temperature-control thermostat senses compartment heat with a capillary bulb and cycles the heating circuit to maintain your set temperature. Replacing a worn thermostat restores more consistent performance and helps correct underheating, overheating, and erratic temperature swings.

• Regulates heat to match the temperature you set
• Senses temperature via an integral capillary tube and sensor bulb
• Opens and closes contacts to control the heating element or burner
• Failure symptoms can include long warm-up, inaccurate temps, overheating, or uneven results

• Disconnect power and, if applicable, shut off gas; allow the unit to cool completely.
• Handle the capillary tube carefully—do not kink, crease, or cut it.
• Route the sensor bulb and tubing through original clips and path for accurate sensing.
• After installation, perform temperature calibration per service instructions if required.

This gas sensor monitors moisture levels during sensor-cook cycles so the control can adjust time and power for consistent results. Replacing a failed sensor restores reliable sensor-cook performance. What it does:

• Detects steam/vapor inside the cavity and sends feedback to the control board
• Helps the appliance automatically set or adjust cooking time on sensor settings
• Failure symptoms can include sensor-cook not starting, stopping early, or running too long
• May trigger "Sensor" or general error messages related to sensor-cook functions

• Disconnect power before servicing; if working on a microwave, discharge the high-voltage capacitor
• Access is typically behind the control panel or air channel; avoid touching/contaminating the sensing surface
• Transfer any mounting clips/brackets and ensure the wiring connector is fully seated
• After installation, run a simple sensor-cook test to confirm operation

The Door Key is an OEM part for GE microwaves. It is responsible for securely holding the microwave door closed during operation. A sturdy and reliable latching mechanism is important for safety and to prevent leaks of electromagnetic radiation.

Causes of a bad latch can include worn or damaged parts due to normal wear and tear over time. The mechanism undergoes a lot of opening and closing stress with repeated use. Impacts from improper handling can also damage latch components.

Symptoms of a bad latch include:

• The door not closing or latching securely
• Difficulty opening or closing the door
• The latch making loud noises or feeling loose

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Guide roller assembly that restores smooth, stable movement for a sliding rack or appliance drawer. Replaces worn or broken rollers to reduce sticking, grinding, or misalignment during use. What it does:

• Guides a sliding rack/drawer so it opens and closes evenly without binding
• Helps stop noisy or jerky movement caused by damaged or worn rollers
• Restores proper alignment to prevent racks from slipping or dropping
• Used where a roller rides along a track or guide to support smooth travel

• Disconnect power (and gas, if applicable) and remove any loose items from the appliance before beginning.
• Remove the affected rack/drawer or access panel to reach the guide; keep mounting hardware for reuse unless damaged.
• Align the guide and reinstall hardware securely; test the rack/drawer movement before completing reassembly.
• If mounting clips or brackets are broken, replace those parts as needed for a secure fit.

This stainless steel microwave door handle restores a solid, comfortable grip for opening and closing the door and refreshes the appliance's appearance when the original handle is damaged or worn.

• Attaches to the door and serves as the primary handhold for opening and closing
• Replaces cracked, loose, or missing handles
• Helps address difficulty opening the door caused by a damaged handle
• Matches stainless models for a consistent, factory look

• Disconnect power to the microwave before servicing
• Access the handle's mounting screws from the inside of the door; carefully release the inner trim to reach fasteners
• Support the door while working and start screws by hand
• Do not overtighten mounting screws to avoid damaging the door panel

A magnetron thermostat that helps prevent the microwave's high-voltage magnetron from overheating, protecting the component and helping restore proper heating when the original thermostat fails. Installs behind the microwave's magnetron assembly. What it does

• Acts as a thermal cutoff for the magnetron to stop operation if temperatures exceed safe limits.
• Common symptom: microwave runs but does not heat or heats intermittently.
• Common symptom: appliance shuts down unexpectedly or trips thermal protection.
• Helps prevent damage to the magnetron from sustained overheating.

• One magnetron thermostat

• Install only with power disconnected; high-voltage microwave components can store lethal charge—discharge the high-voltage capacitor before service.
• Verify correct part fit and orientation behind the magnetron; follow OEM wiring and mounting locations.
• Only replace this part if the existing thermostat is confirmed faulty; check related components (magnetron, high-voltage diode, capacitor) as needed.

This factory glass panel replaces a cracked, shattered, or missing original, restoring a clean, safe cover/viewing surface on your appliance. It helps protect internal areas from splatter and keeps the assembly looking and fitting the way it should.

• Replaces a damaged glass component within the original assembly on applicable models
• Restores a clear, smooth surface for proper appearance and function
• Helps shield underlying parts from spills, grease, and debris
• Common symptoms: cracked or shattered glass, missing piece, sharp edges, looseness/rattling

• Disconnect power before servicing; allow all surfaces to cool
• Wear cut-resistant gloves and eye protection; handle edges carefully
• Support the panel/door during removal and installation to prevent stress on frames/hinges

This holder nut assembly secures a component to the appliance frame, restoring proper mounting and reducing vibration or movement. Replace a damaged or missing holder nut to keep connected parts stable and functioning. What it does:

• Secures a component or assembly to the appliance frame or mounting bracket
• Prevents looseness, rattling, and misalignment caused by worn or missing mounting hardware
• Restores a safe, stable connection that helps maintain normal operation
• Matches OEM mounting geometry for a direct replacement when the original nut is damaged

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the mounting area by removing the appropriate panel or cover per your model's service instructions
• Start threads by hand to avoid cross-threading, then tighten with the correct tool; do not overtighten
• If any fasteners or nearby components are damaged, replace them as needed for a secure installation